Giropes Baxtran OPTIMA PTO Benutzerhandbuch Seite 7

REPARATION AND MAINTENANCE
HYDRAULIC OIL SUPPLY
Check the oil every six months. We recommend you to use the hydraulic oil: ISO VG32, a 400C its kinematics viscosity is of 32
cSt, the total 0.3 liters.
Due to transport or reversal, it is possible that some air gets into the hydraulic bomb, and this fact can cause a problem in the
forklifts. Perhaps they are not going to rise when they are in an ascending position.
The following method can help the user to avoid the problem: The user must move the lever from the ascending position to the
ascending position more than once, repeating the process.
ROUTINES OF MAINTENANCE AND REPARATION
The routine of maintenance is essential. The user must center this revision in the wheels and the mandrel, retire all the strange
bodies and objects which are placed on the wheels, and also avoid that the wheels get poked.
When the wheels are free of dirtiness and strange objects, the user must retire the load and place the forklifts downwards until they
reach their lowest position.
LUBRICANT
When the lever of regulation is in factory, we apply different long life lubricants both to the bearings and the axis, the user only need
to apply the lubricant once a month or every time that the user proceeds to do an in-depth revision.
SECURITY GUIDE
1. Before proceeding to use the hand pallet, the user must read the following guide of instructions carefully.
2. The user must bear in mind that before pulling of the hand pallet , it is necessary to rise the forklifts a little.
3. When the user pulls of the hand pallet, it is important to keep the lever in a medium position. In such way, it will be easier to move
the hand pallet and the bounces of the piston of the lever will be reduced. Moreover, it will also protect the seal of the liquid and
the components of the piston. All this is important because it helps the life and usefulness of the hand pallet.
4. The hand pallet must be used and handled by people who have the appropriate qualification on how to use it.
5. Before proceeding to use the hand pallet, the user must revise the wheels, the levers and the forklifts.
6. Don't use the hand pallet on oblique surfaces.
7. Don't put a person on the forklift.
8. It is recommended that the operator wears gloves and security footwear.
9. In the process of elevation and transport of load, all the workers which are near the hand pallet must keep themselves far from
the forklifts, at least at a distance of 600 mm.
10. The user must pay a lot of attention in the way of charging the pallet and avoid the slope or deviation of the load. (see figure 2 B)
11. The user must not exceed the maximum capacity of the hand pallet.
12. The user must use the hand pallet with care in special circumstances and placements.
WAY OF ADJUSTING THE HAND PALLET
1. Disconnect the socket of the indicator.
2. Adjust the digital multimeter in the scale of "200 Ω" to measure the resistance of each group of "10 Ω". Ways of adjustment:
Connect an end to the multimeter of d "E+" and then with the other end to check each group of "E +" A, B, C and D. Adjust
all the groups to "10 Ω". Now connect an end of the multimeter to "E-" and with the other end check every group of the "E-"
A, B, C and D. You must at least realize 8 measures and finally disconnect the multimeter.
3. Insert the socket to the indicator and connect it.
4. Place the weight in the frontal part, in the middle and in the back part of the forklifts, check that the value of the weight is the
same, if it is not so, you must adjust a little the groups C and D in the plate of the circuit:
- If the value is not correct when the load is placed in the frontal part of the forklift, the user must adjust "D +" of the
group D, following the direction of the hands of the clock if the variations are small and against the direction of the hands
of the clock if the variations are bigger.
USER'S MANUAL ARX EN EN
7