Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
MAIN SCREEN
HOT WATER MAINTENANCE
NOW
MAINTAIN TEMPERATURE
Contains 3 areas:
1. Actual Maintain temperature (blue area)
2. Next event temperature (grey area)
3. Hot water storage temperature (white area - if water heater sensor is connected
SYSTEM
and active
INFO, RESET, SERVICE, TEST....
Additional icons for settings, relay ON/OFF), key lock or warning will be displayed.
HOT WATER MAINTENANCE
HEATING CABLE & PIPE
When lock is "ON" a password is needed to access the parameter menus.
CABLE TYPE, PIPE DAIMETER,...
After the correct 4 numbers password is entered, each parameter in the setup can be
GENERAL SETTINGS
changed. The unit locks again after 10 minutes timeout (mo keys pressed).
NOW
COUNTRY, LANGUAGES, UNITS,...
WATER TEMP. & PROGRAM
SETTINGS
APPARTMENT, MAINTAIN, ECONOMY,....
SYSTEM
INFO
INFO, RESET, SERVICE, TEST, ...
HEATING CABLE & PIPE
TEST PROGRAM
CABLE TYPE, PIPE DAIMETER, ...
GENERAL SETTINGS
COUNTRY, LANGUAGES, UNITS, ...
RESET
WATER TEMP. & PROGRAM
APPARTMENT, MAINTAIN, ECONOMY, ...
SERVICE
STATUS
SYSTEM
INFO
TEST PROGRAM
INFO
SELECT CABLE TYPE
RESET
TEST PROGRAM
SELECT PIPE DIAMETER
SERVICE
RESET
SELECT INSULATION THICKNESS
STATUS
SERVICE
SELECT AMBIENT TEMPERATURE
KEYLOCK FEATURE
STATUS
SELECT BOILER SENSOR
Info
SELECT BOILER CUT-OFF TEMPS.
Test
program
SELECT CABLE TYPE
Reset
SELECT PIPE DIAMETER
SELECT CABLE TYPE
Service
SELECT INSULATION THICKNESS
SELECT PIPE DIAMETER
Status
SELECT AMBIENT TEMPERATURE
SELECT INSULATION THICKNESS
SELECT BOILER SENSOR
SELECT AMBIENT TEMPERATURE
SELECT BOILER CUT-OFF TEMPS.
SELECT BOILER SENSOR
SELECT BOILER CUT-OFF TEMPS.
Key
lock
48 | Domotec.ch
SETTING
HOT WATER MAINTENANCE
NOW
SETTINGS
SYSTEM
SETTING
SYSTEM
INFO, RESET, SERVICE, TEST....
HEATING CABLE & PIPE
CABLE TYPE, PIPE DAIMETER,...
GENERAL SETTINGS
COUNTRY, LANGUAGES, UNITS,...
SYSTEM
WATER TEMP. & PROGRAM
SYSTEM
APPARTMENT, MAINTAIN, ECONOMY,....
HEATING CABLE & PIPE
General info about the unit, name, commissioning date, firmware
version, Domotec contact info.
The test programme runs for 30 minutes, during which all
HEATING CABLE & PIPE
parameters will be ignored to check the heating cable and the
connection on site. You can stop the test programme at any time.
HWAT-M
HEATING CABLE & PIPE
Select "YES" to activate the Quick install menu and return all
settings to factory settings.
DN 25
Quick start process restarts automatically.
Access for Domotec technicians.
40 MM
Info on current status of the control unit:
20 °C
Pipe temperature
Water heater temperature
Maintain temperature
ON
Supply voltage
Duty cycle
35/85 °C
Power output
Max power output
Load current
When key lock is "ON", the setup and timer menus are protected
by password. To unlock the unit, enter the predefined password
(3000). The unit will automatically lock itself after 10 mins of
inactivity or when lock "on" key is pressed.
To deactivate the key lock, press "oFF".
14 : 14
NEXT
ECONOMY TEMP
AT 17:00
BOILER
14 : 17
14 : 14
NEXT
ECONOMY TEMP
NEXT
AT 17:00
BOILER
ECONOMY TEMP
14 : 17
14 : 17
AT 17:00
BOILER
14 : 17
14 : 17
HWAT-M
DN 25
40 MM
20 °C
ON
35/85 °C
14 : 17
HWAT-M
DN 25
40 MM
20 °C
ON
35/85 °C
grey area
SELECT LANGUAGE
SELECT COUNTRY
white area
SELECT DATE
SELECT TIME
blue area
SELECT ALARM
SELECT SAVING TIME
SELECT LANGUAGE
SELECT WATER TEMPRATURE
14 : 14
SELECT COUNTRY
SELECT LANGUAGE
SELECT PROGRAM
SELECT DATE
SELECT COUNTRY
PROGRAM TIMER
SELECT TIME
SELECT DATE
SELECT ALARM
SELECT TIME
SELECT SAVING TIME
SELECT ALARM
14 : 17
SELECT SAVING TIME
SELECT WATER TEMPRATURE
SELECT PROGRAM
SELECT WATER TEMPRATURE
14 : 17
PROGRAM TIMER
SELECT PROGRAM
PROGRAM TIMER
14 : 17
GENERA
WATER T
Werbung
Inhaltsverzeichnis
