Using The Gas Table With An Integrated Piezo Igniter; Cleaning And Care - Petromax ge45-s Gebrauchsanleitung

Before using the Gas Table
DE
Check the hose for kinks, cracks, porous areas, wear or cuts before each
EN
use of the Gas Table. If you notice any damage to the hose, even seemingly
minor damage, do not use the Gas Table. Only replace the hose with an
FR
approved replacement hose with a suitable pressure reducer. If you have
any questions, please contact your local retailer. You can find the contact
BG
details of our retailers on our website at www.petromax.de
CZ

Using the Gas Table with an integrated piezo igniter

Before you use the cooking zones of the Gas Table, follow all the steps in the sections
DA
Assembly and initial operation and Instructions for connecting the gas supply – LP
gas properly and read and understand the safety instructions. Follow the steps below to
EE
ignite one of the gas burners of the Gas Table and use it for cooking. Always ignite one
cooking zone after the other (never light both at the same time!)
ES
• Do not yet place any Dutch Ovens, Skillets or other cookware on the switched-off
FI
cooking zone.
• Open the gas valve of the gas cylinder.
GR
• Press the control knob in the "OFF" [•] position and turn it to the left to "Ignition" [ ].
HR
The gas supply is now open and gas flows into the burner. Keep the knob pressed and
turn it further left to "MAX" [ ]. You will hear a click and at the same time the ignition
HU
will spark. Keep the control knob pressed for approx. 5 seconds, otherwise the flame
monitor will cut the gas supply and the ignition process will be interrupted. When you
IS
release the knob, the flame should burn.
• If the ignition process was not successful, repeat the process.
• If the flame goes out (e.g. due to wind), the valve closes automatically, and the gas
supply is stopped. This flame monitoring ensures safety when using the Petromax Gas
Table.
• Turn the control knob of the cooking zone you want to use to the "MIN" [ ] position
to check the flame size.
• At the "MAX" position [ ] the flame should be large. At the "MIN" position [ ] the flame
should be small. The flame should burn evenly in any position. If the flame flutters,
follow the instructions in the Troubleshooting section or contact your local retailer
or our customer service.
• Place fire Dutch Ovens or Fire Skillets on the cooking zone to start preparing food.
• Observe the minimum and maximum cookware diameter of 15 cm and 35 cm respec-
tively. Do not use cookware with a larger or smaller diameter. Use the control knob to
regulate the size of the flame and thus the desired output for the cooking zone.
If the ignition of the gas burner does not work after several attempts using
the control knob, contact your retailer or customer service.
Do not lean over the Gas Table when it is in use. When lighting the Gas
Table, keep your face, body and clothing at least 30 cm away from the
ignition openings.
If the Gas Table should tip over during operation or if objects in immedi-
ate vicinity catch fire, shut off the gas supply IMMEDIATELY. To do this,
you must close the gas cylinder valve and the gas supply control knob
on the device.
Manual ignition of the gas burner
• Make sure that the controller is in the "OFF" [•] position.
• Open the valve of the gas cylinder as explained in the instructions for the gas cylinder
and the regulator.
• If you want to use a match, we recommend that you use an extra-long match. Ignite
it and hold it directly near the ignition openings of the gas burner.
14 14
• Turn on the gas supply of the cooking zone.
• Check that the burner has ignited evenly and that the flame burns evenly.
Wear appropriate clothing when usingthe Gas Table. Long, wide sleeves
can easily catch fire.
Do not lean over the Gas Table when it is in use. When lighting the Gas
Table, keep your face, body and clothing at least 30 cm away from the
ignition openings.
If after several attempts the ignition of the gas burner does not work
either manually or by using the control knob, contact your retailer or
our customer service.
Switching off the gas burner and disconnecting the gas cylinder
Follow the steps below if you want to turn off the Gas Table:
• Turn off the gas supply at the fuel valve of the gas cylinder by closing the gas valve.
As soon as the flame on the burner goes out, turn the gas burner control knob to the
"OFF" position [•] and let the Gas Table cool down completely. We recommend a waiting
period of at least 30 minutes. Disconnect the gas cylinder properly from the Gas Table.
The primary air setting of the gas burner is pre-set and screwed in place.
Do not under any circumstances make changes to the primary air setting.
This may only be done by a qualified person in the event of a defect.
The gas nozzle is an essential part of the ignition system. You are not
allowed to remove or change it by yourself. In case of a possible defect,
replacement is only permitted by a qualified person.

Cleaning and care

Do not clean the Gas Table when it is in operation or still connected to
the gas cylinder.
Only clean the Gas Table when it has cooled down completely.
Do not clean the Gas Table with oven cleaner, abrasive cleaners (kitchen
cleaners), cleaners with citrus ingredients or other aggressive or even
flammable cleaning agents. Do not use scouring sponges for cleaning.
Especially the coated surfaces of the Gas Table are very sensitive.
Do not immerse the Gas Table in water.
You can clean all parts of the Petromax Gas Table from food residues and dirt using standard
cleaning agents (e.g. dishwashing detergent, all-purpose / neutral cleaner, etc.). Coated
surfaces of the Gas Table must always be cleaned particularly carefully. Follow the steps
below to clean the Gas Table. Switch off the Petromax Gas Table completely and wait
until it has fully cooled down.
1. Disconnect the Gas Table properly from the gas cylinder.
2. Carefully remove grease and other residues from the surfaces of the Gas Table as well as from the
windscreen with warm soapy water and a lint-free cloth and wipe with clean water.
3. Remove moisture residues completely with a dry cloth.
4. We recommend that you clean the gas burners at least once a year using a standard
pipe cleaner.