General Safety Standards; Electrical Safety; Personal Safety - Felisatti NTF250/1200ST Bedienungsanleitung

lever switch. We recommend using this device only
with the greatest caution.
Although this tool has been designed and
constructed in order to permit operators to work
in the greatest conditions of safety, the following
precautions must be taken in particular work
conditions:
Adequate safety gloves and
eyewear.
The tool has been designed and constructed to
reduce noise to minimum levels (see technical data
2.1). In particular working conditions the maximum
sound level at the place of work may exceed 85 Db(A)
and therefore create a risk to health and hearing.
In this case the operator must use ear
protectors.
Work carefully and maintain the tool in perfect working
order, for your own safety.
2.4.1 SWITCH (fig. 2)
Although the switch on your mitre saw prevents
accidental starting, a LOCK in "ON" button has been
provided. Respect the warnings provided in Point 4.4.
Switch operation
- Starting - To start the machine, press the lever
switch A and keep it pressed (fig. 2)
- Lock in "ON" - The switch can be locked in "ON"
position by first pressing the lever switch A to start the
motor and then pressing the LOCK in "ON" button B
(fig. 2)
Warning! In order to release the switch, press the
black lever A and then release it. (fig. 2)
Protection – The switch is equipped with a airtight
protection that provides protection against penetration
by dust and foreign bodies in general.

3 GENERAL SAFETY STANDARDS

WARNING! Read all instructions. Failure to follow
all instructions listed below may result in electric
shock, fire and/or serious injury.
The term "power tool" in all of the warnings listed
below refers to your mains operated (corded)
power tool or battery operated (cordless) power
tool.Electrónica constante (mod. AF125/1100VES)
SAVE THESE INSTRUCTIONS
1) WORK AREA
a) Keep work area clean and well lit. Cluttered and
dark areas invite accidents.
b) Do not operate power tools in explosive
atmospheres, such as in the presence of flammable
liquids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.
c) Keep children and bystanders away while
operating a power tool. Distractions can cause you
to lose control.

2) ELECTRICAL SAFETY

a) Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power tools.
Unmodified plugs and matching outlets will reduce
risk of electric shock.
b) Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
c) Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electric shock.
protective
d) Do not abuse the cable. Never use the cable for
carrying, pulling or unplugging the power tool. Keep
cable away from heat, oil, sharp edges or moving
parts. Damaged or entangled cables increase the risk
of electric shock.
e) When operating a power tool outdoors, use an
extension cable suitable for outdoor use. Use of a
cable suitable for outdoor use reduces the risk of
electric shock.

3) PERSONAL SAFETY

a) Stay alert, watch what you are doing and use
common sense when operating a power tool. Do
not use a power tool while you are tired or under the
influence of drugs, alcohol or medication. A moment
of inattention while operating power tools may result
in serious personal injury.
b) Use safety equipment. Always wear eye protection.
Safety equipment such as dust mask, non-skid safety
shoes, hard hat, or hearing protection used for
appropriate conditions will reduce personal injuries.
c) Avoid accidental starting. Ensure the switch is in
the off position before plugging in. Carrying power
tools with your finger on the switch or plugging in
power tools that have the switch on invites accidents.
d) Remove any adjusting key or wrench before turning
the power tool on. A wrench or a key left attached to a
rotating part of the power tool may result in personal
injury.
e) Do not overreach. Keep proper footing and balance
at all times. This enables better control of the power
tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves away
from moving parts. Loose clothes, jewellery or long
hair can be caught in moving parts.
g) If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of these devices
can reduce dust related hazards.
4) POWER TOOL USE AND CARE
a) Do not force the power tool. Use the correct power
tool for your application. The correct power tool will
do the job better and safer at the rate for which it was
designed.
b) Do not use the power tool if the switch does not turn
it on and off. Any power tool that cannot be controlled
with the switch is dangerous and must be repaired.
c) Disconnect the plug from the power source before
making any adjustments, changing accessories, or
storing power tools. Such preventive safety measures
reduce therisk of starting the power tool accidentally.
d) Store idle power tools out of the reach of children