Installation And Connection - Panasonic NE-1027 Bedienungsanleitung

Examine your microwave oven
Unpack the oven, remove all packing material, and
examine the oven for any damage such as dents,
broken door latches or cracks in the door. If you find
any damage, notify your dealer immediately. Do not
install a damaged microwave oven.
Earthing instructions
IMPORTANT: THIS UNIT HAS TO BE PROPERLY
EARTHED FOR PERSONAL SAFETY.
If your AC outlet is not grounded, it is the personal
responsibility of the customer to have it replaced with a
properly grounded wall socket.
Operation voltage
The voltage has to be the same as specified on the
label on the oven. If a higher voltage than specified is
used, it may cause a fire or other damages.
Placement of the Oven
1. Place the oven on a flat and stable surface.
2. When this oven is installed, it should be easy to
isolate the appliance from the electricity supply by
pulling out the plug operating a circuit beaker.
3. For proper operation, ensure a sufficient air
circulation for the oven.
Counter-top use:
a. Allow 15 cm of space on the top of the oven,
10 cm at back and 5 cm on both sides.
b. If one side of the oven is placed flush to a wall,
the other side or top must not be blocked.
5 cm
4. Do not place this oven near an electric or gas
cooker range.
5. The feet should not be removed.
6. This oven is only for household usage. Do not use
outdoors.
7. Avoid using the microwave oven in high humidity.
8. The power cord should not touch the outside of the
oven. Keep the cord away from hot surfaces.
NE-1027_EYG.indb 8

Installation and Connection

15 cm
10 cm
- 8 -
Do not let the cord hang over the edge of a table or
work top. Do not immerse the cord, plug or oven in
water.
9. Do not block the air vents on the top and back of
the oven. If these openings are blocked during
operation the oven may overheat. In this case the
oven is protected by a thermal safety device and
resumes operation only after cooling down.
Caution
This appliance is delivered without a plug and must be
installed by a qualified electrician to a 16 A fused
power supply 400 V 3/N/PE 50 Hz. Installation must
conform to local rules and standards. Please refer the
data on the nameplate.
IMPORTANT: The wires in the mains lead are coloured
in accordance with the following:
Green and Yellow: Earth
Blue: Neutral
A precise assignment of the live wires is not necessary
as the connection is not dependant on phase
sequence. The colour of the live wires may vary.
Safety Instructions
Warning
1. The door seals and door seal areas should be
cleaned with a damp cloth.
The appliance should be inspected for damage to
the door seals and door seal areas and if these
areas are damaged the appliance should not be
operated until it has been repaired by a service
technician trained by the manufacturer.
2. Do not operate this appliance if it has a damaged
CORD OR PLUG, if it is not working properly, or if it
has been damaged or dropped. It is dangerous for
anyone other than a service technician trained by
the manufacturer to perform repair service.
3. Do not attempt to tamper with or make any
adjustments or repairs to the door, control panel
housing, safety interlock switches or any other part
of the oven. Do not remove the outer panel from
oven.
Repairs should only be done by a qualified service
person.
If the supply cord is damaged, it must be replaced
by the manufacturer or its service agent or a
similarly qualified person in order to avoid a hazard.
4. When it becomes necessary to replace the oven
light, please consult your dealer.
5. Only allow children and persons with reduced
physical, sensory or mental capabilities, or lack of
experience and knowledge, to use the oven without
supervision when adequate instructions have been
given so that the child and such person is able to
use the oven in a safe way and understands the
hazards of improper use. And children should be
supervised to ensure that they do not play with the
appliance.
2020/11/24 10:21:53