Switching Off - EINHELL GE-LC 18 Li T Kit Originalbetriebsanleitung

5.11 Fitting the battery (Fig. 22 – 23)
Press the side pushlock button (T) of the battery
pack as shown in Fig. 22 and push the battery
pack into the mount provided. When the battery
pack is positioned as in Fig. 23, make sure that
the pushlock button latches in place! To remove
the battery pack, proceed in reverse order.
5.12 Charging the battery (Fig. 24)
1. Take the battery pack out of the equipment.
Do this by pressing the pushlock button (T).
2. Check that your mains voltage is the same as
that marked on the rating plate of the battery
charger. Insert the power plug of the charger
(21) into the mains socket outlet. The green
LED will then begin to fl ash.
3. Insert the battery pack (1) into the battery
charger (21).
4. In the section entitled „Charger indicator" you
will fi nd a table with an explanation of the LED
indicator on the charger.
The battery pack can become a little warm during
the charging. This is normal.
If the battery pack fails to charge, check:
•
whether there is voltage at the socket outlet
•
whether there is good contact at the charging
contacts.
If the battery pack still fails to charge, send
•
the charging unit
•
and the battery pack
to our customer service center.
To ensure that the battery pack provides long ser-
vice, you should take care to recharge it promptly.
You must recharge the battery pack when you
notice that the power of the cordless equipment
drops. Never fully discharge the battery pack. This
will cause it to develop a defect.
6. Operation
Please note that the statutory regulations gover-
ning noise abatement may diff er from one loca-
tion to another.
Caution! Always use the shoulder strap when
working with the equipment. Always switch off the
equipment before you take off the shoulder strap.
Otherwise there is a risk of injury.
Put on the shoulder strap as described above, fi t
the required mounting kit and adjust the equip-
Anl_GE_LC_18_Li_T_SPK7.indb 26 Anl_GE_LC_18_Li_T_SPK7.indb 26
GB
ment to suit your needs.
Switching on/off
Switching on
•
Hold the equipment by the handles with both
hands (thumbs under the additional handle).
•
Slide the safety lock-off (Fig. 3/Item 4) to the
front and hold.
•
Switch on the equipment with the On/Off
switch (Fig. 3/Item 3). You can then release
the safety lock-off.
Switching off
Release the On/Off switch (Fig. 3/Item 3).
7. Working with the chainsaw
mounting kit
Preparations
To ensure that you can work safely, check the fol-
lowing points before every use:
Condition of the chainsaw
Inspect the chainsaw before the start of work for
damage to the housing, the power cable, the saw
chain and the cutter rail. Never use a chainsaw
which is obviously damaged.
Oil container
Fill level of the oil container. Even while working,
keep checking that suffi cient oil is in the system.
To avoid damaging the chainsaw, never run the
saw if there is no oil in the system or if the oil
drops below the "min" mark. On average, a single
fi lling will last around 20 minutes depending on
the number of pauses in cutting and the loads
involved.
Saw chain
Tension of the saw chain, condition of the cutting
ele-ments. The sharper the chainsaw, the easier
and more controllable it is to operate the chain-
saw. The same also applies to the chain tension.
Also while working you should check the chain
tension no less than every 10 minutes in order to
increase your safety. New saw chains in particular
often tend to expand more.
Safety clothing
Always wear appropriate tight-fi tting safety
clothing like special trousers which protect
against cuts, protective gloves and safety shoes.
- 26 -
11.08.14 13:08 11.08.14 13:08