Protecting The Environment - Black & Decker BES701 Bersetzt Von Den Originalanweisungen

After use
After use, wipe off chips and dust adhering to the tool with
u
a cloth or the like.
Keep the blade guard clean according to the directions in
u
the previously covered section.
Lubricate the sliding portions with machine oil to prevent
u
rust.
When storing the tool, pull the carriage toward you fully.
u
Carrying the tool
Make sure the tool is unplugged.
u
Secure the blade at the 0° bevel angle and turn the base
u
to the right mitre angle fully
Secure the slide bars after pulling the carriage toward you
u
fully.
Lower the handle fully and lock it in the position by
u
pushing in the saw head locking pin (17).
Carry the tool by holding under the base.
u
If you remove the clamp, dust bag, etc., you can carry the
u
tool more easily.
Carry the tool by with both hands holding the tool base.
u
Caution! Always secure all moving portions before carrying
the tool.
Saw head locking pin (17) is for carrying and storage
purposes only and not for any cutting operations.
Troubleshooting
Problem Possible Cause
Motor does
Saw not plugged in.
not start
Mitre table
unlocked.
Angle of cut
inaccurate
Too much sawdust
under table.
Parts Failure.
Pivot spring not
Cutting arm
replaced properly
cannot fully
after service.
raise, or blade
guard cannot
Sawdust build up.
fully close
Saw head locking
pin not set properly.
Saw blade
damaged.
Blade binds,
Dull blade.
jams or
shakes
Improper blade.
Warped blade.
Saw blade
damaged.
Saw blade
loosened.
Saw vibrates
or shakes
Saw not properly
fastened down.
Work piece not
properly supported.
Solution
Check that all cords are plugged in.
Use mitre table locking lever (see
Adjusting the mitre angle section.
Vacuum or blow out dust. Wear eye
protection.
Contact service centre.
Contact service centre.
Clean and lubricate moving parts.
Check, adjust, and properly set saw
head locking pin.
Replace blade.
Replace or sharpen blade.
Replace blade.
Replace blade.
Replace blade.
Tighten arbor bolt.
Fasten saw to bench, stand or table.
Properly support or clamp work
piece.
(Original instructions)
Z

Protecting the environment

Separate collection. Products and batteries marked
with this symbol must not be disposed of with normal
household waste.
Products and batteries contain materials that can be
recovered or recycled reducing the demand for raw materials.
Please recycle electrical products and batteries according to
local provisions. Further information is available at
www.2helpU.com
Technical data
Voltage
Speed
Blade outer diameter
Bore diameter
Weight
Blade thickness
Blade max. kerf
Mitre (max. positions)
Bevel (max. positions)
Max. cross-cut capacity at 90 °
Max mitre capacity at 45 °
Max. dept cut at 90 °
Max. dept cut at 45 °
BES701 - Level of sound pressure according to EN 62841:
L (sound pressure) 98 dB(A), Uncertainty (K) 3 dB(A)
pA
L (sound power) 108.0 dB(A), Uncertainty (K) 3 dB(A)
WA
Supply of Machinery (Safety)
Regulations 2008
BES701 Sliding Compound Mitre Saw
Black & Decker declares that these products described under
"technical data" are in compliance with:
The Supply of Machinery (Safety) Regulations, 2008, S.I.
2008/1597 (as amended),
EN62841-1:2015, EN 62841-3-9:2020+A11:2020
These products conform to the following UK Regulations:
Electromagnetic Compatibility Regulations, 2016,
S.I.2016/1091 (as amended).
The Restriction of the Use of Certain Hazardous Substances
in Electrical and Electronic Equipment Regulations 2012, S.I.
2012/3032 (as amended).
ENGLISH
BES701 Type 1
V
/min 4800
mm
mm
kg 12.1
mm
mm
° +/- 47
°
mm
mm
mm
mm
230
216
30
2.6
2.8
47
220
155
70
40
17