Installation Precautions; General Safety Information - V2 AYROS 800-230V Bedienungsanleitung

GENERAL WARNINGS:
SAFETY - INSTALLATION
m
The following warnings are taken directly from the
Regulations and apply, as far as possible, to the product
described herein
CAUTION Important safety instructions. Observe all the
instructions as improper installation may cause serious
damage
CAUTION Important safety instructions. It is important to
comply with these instructions to ensure personal safety.
Store these instructions
• Before commencing the installation, check the "Product
technical specifications", in particular whether this product
is suitable for automating your guided part. Should it be
unsuitable, DO NOT proceed with the installation
• The product cannot be used before it has been commissioned
as specified in the "Testing and commissioning" chapter
CAUTION According to the most recent European
legislation, the implementation of an automation system
must comply with the harmonised standards set forth in
the Machinery Directive in force, which allow for declaring
the presumed conformity of the automation. On account
of this, all operations regarding connection to the mains
electricity, as well as product testing, commissioning and
maintenance, must be performed exclusively by a qualified
and skilled technician!
• Before proceeding with the product's installation, check that
all materials are in good working order and are suitable for the
intended applications
• The product is not intended for use by persons (including
children) with reduced physical, sensory or mental capacities,
nor by anyone lacking sufficient experience or familiarity with
the product
• Children must not play with the appliance
• Do not allow children to play with the control devices of the
product. Keep the remote controls out of reach of children
CAUTION In order to avoid any danger from inadvertent
resetting of the thermal cut-off device, this appliance must
not be powered through an external switching device,
such as a timer, or connected to a supply that is regularly
powered or switched off by the circuit
• Provide a disconnection device (not supplied) in the plant's
mains power supply, with a contact opening distance that
ensures complete disconnection under the conditions
envisaged by Overvoltage Category III
• Handle the product with care during installation, taking care
to avoid crushing, knocks, falls or contact with liquids of
any kind. Keep the product away from sources of heat and
open flames. Failure to observe the above can damage the
product and increase the risk of danger or malfunctions. If this
should happen, stop installation immediately and contact the
Customer Service
• The manufacturer assumes no liability for damage to property,
items or persons resulting from non-compliance with the
assembly instructions. In such cases the warranty does not
cover material defects
• The weighted sound pressure level of the emission A is lower
than 70 dB(A)
• Cleaning and maintenance to be carried out by the user must
not be effected by unsupervised children
• Before intervening on the system (maintenance, cleaning),
always disconnect the product from the mains power supply
• Check the system periodically, in particular all cables, springs
and supports to detect possible imbalances, signs of wear or
damage. Do not use the product if repairs or adjustments are
necessary, since an installation failure or an incorrectly balanced
door may cause injury
• The packaging materials of the product must be disposed of in
compliance with local regulations
• Keep persons away from the gate when it is moved through
the control elements
• When performing a manoeuvre, keep an eye on the automated
mechanism and keep all bystanders at a safe distance until the
movement has been completed
• Do not operate the automation if anyone is working on it;
disconnect the power supply before permitting any work to be
carried out
• If the power cable is damaged, it must be replaced by the
manufacturer or by the latter's technical assistance service, or
by a similarly qualified person, in order to prevent any type of
risk

INSTALLATION PRECAUTIONS

• Prior to installing the drive motor, check that all mechanical
components are in good working order and properly balanced,
and that the automation moves correctly
• If the gate or door being automated has a pedestrian gate,
then the system must include a control device that will inhibit
the operation of the motor when the pedestrian gate is open
• Make sure that the control devices are kept far from moving
parts but nonetheless in a visible position. Unless a selector is
used, the control devices must be installed at a height of at
least 1.5 m and must not be accessible
• That windows, having a gap exceeding 200 mm when open,
are to be closed using a biased-off switch if the opening
movement is controlled by a fire-sensing system
• Ensure that entrapment between the driven part and the
surrounding fixed parts due to the opening movement of the
driven part is avoided
• Permanently fix the label concerning the manual release
adjacent to its actuating member
• After installing the drive motor, make sure that the mechanism,
protective system and all manual manoeuvres operate properly
- 32 -