Technische Daten/Technical Specifications - AER Domino 2A Bedienungsanleitung

6. Technische Daten/Technical specifications

Inputs
channel 1/4 Instrument / line input, high impedance,
unbalanced
Stereo jack socket*:
Nom. input voltage:
High/low (attenuator) switch:
Min. input voltage:
Max. input voltage (THD = 1%):
Input impedance:
Signal / noise ratio (A-weighted):
Equivalent input noise voltage
(A-weighted):
Phantom power (switchable):
Load current:
Short circuit protected.
*Ring used for phantom power.
clip indicator Headroom:
channel 2/3 Switchable input with line and microph. mode
Combo socket:
line mode (jack input only)
Instrument / line input, high impedance,
unbalanced
Nom. input voltage:
Min. input voltage:
Max. input voltage:
Input impedance:
Signal / noise ratio (A-weighted):
Equivalent input noise voltage
(A-weighted):
mic mode (channel 2)
Microphone input, XLR (balanced), stereo jack
(balanced), mono jack (unbalanced)
Nom. input voltage:
Min. input voltage:
Max. input voltage:
Input impedance (balanced):
Input impedance (unbalanced):
Voice filter (referred to 10 kHz):
Signal / noise ratio (A-weighted):
Equivalent input noise voltage
(A-weighted):
Phantom power (XLR only):
Supply resistors:
Load current:
clip indicator Headroom:
return
Input for external parallel effect loop (send /
return), or supplementary input
Mono jack socket:
Nom. input voltage:
Max. input voltage:
18
100 mV (–20 dBV)
high: 21 mV (–34 dBV)
low: 68 mV (–23 dBV)
high: 3.5 V (+11 dBV)
low:
2.2 MΩ || 350 pF
1.8 µV (–115 dBV)
XLR + jack ¼" (6.35 mm)
100 mV (–20 dBV)
27 mV (–31 dBV)
2.2 MΩ || 350 pF
2.7 µV (– 111 dBV)
1 / sleeve = ground,
2 / tip = positive (+),
3 / ring = negative (–)
10 mV (–40 dBV)
3.3 mV (–50 dBV)
with option: 5.8 mV (–45 dBV)
(see notes)
with option:
–10 dB at 270 Hz
1 µV (–120 dBV)
320 mV (–10 dBV)
aux in
¼" (6.35 mm)
–10 dB
Output
L-out, R-out
5 V (+14 dBV)
95 dB
9 V DC
max. 100 mA
approx. 6 dB
line out
7 V (+17 dBV)
headphones Headphones output
92 dB
send
tuner
1 V (0 dBV)
1.6 V (+4 dBV)
1.2 kΩ
2.7 kΩ
DI-out
80 dB
48 V
6.8 kΩ
max. 10 mA
approx. 6 dB
¼" (6.35 mm)
5 V (+14 dBV)
Input impedance:
Auxiliary input, e.g. for CD
Stereo jack socket:
Nom. input voltage:
Min. input voltage,
stereo:
mono:
Max. input voltage:
Input impedance:
Stereo line output after tone controls,
adjustable by pre master, with switchable
stereo simulation, aux in, and effects
2 mono jack sockets,
Output voltage:
adjustable by pre master
Output impedance:
(varies with level setting)
Min. load impedance:
Residual noise (A-weighted): < 1 μV (–120 dBV)
Preamplifier output post master, tone controls,
and effects
Mono jack socket:
Nom. output voltage:
Output impedance:
Min. load impedance:
Residual noise
(A-weighted):
Stereo jack socket:
Output power (THD < 1 %):
8 Ω minimal load impedance
16 Ω 2 x 160 mW max. outpit impedance
When plugged in, the internal speaker is
switched off.
Output pre master, post tone controls, for exter-
nal parallel effect loop (send / return)
Mono jack socket:
Nom. output voltage
Min. load impedance:
Tuner output, post tone controls,
pre effects and master
Mono jack socket:
Nom. output voltage:
Output impedance:
Min. load impedance:
Balanced, non-isolated XLR output, post tone
controls, switchable pre or post effects
1 = ground,
2 = positive (+),
3 = negative (–)
Nom. output voltage
(differential):
Output impedance (per terminal):
Min. load impedance (differential):
20 kΩ
3.5 mm
500 mV (–6 dBV)
100 mV (–20 dBV)
200 mV (–14 dBV)
4 V (+12 dBV)
22 kΩ
1.4" (6.35 mm), L / R
0...1 V (0 dBV),
max. 15 kΩ
2 kΩ
¼" (6.35 mm)
460 mV (–7 dBV)
100 Ω
2 kΩ
4.5 µV (–107 dBV)
¼" (6.35 mm)
¼" (6.35 mm)
1 V (0 dB)
2 kΩ
¼" (6.35 mm)
330 mV (–10 dBV)
47 Ω
2 kΩ
68 mV (–23 dBV)
100 Ω
1 kΩ