Technical Specifications - AER AG83 Bedienungsanleitung

6. Technical specifications

line in Balanced or unbalanced line input
Combo socket, XLR + jack ¼" (6.35 mm)
Nom. input voltage:
Min. input voltage:
Max. input voltage:
Input impedance:
Signal/noise ratio (A-weighted):
Equivalent input noise voltage
(A-weighted):
Phantom power (optional): 9 V DC /
max. 100 mA, on ring of input jack,
short circuit protected.
External equipment may be damaged by inappropri-
ate use of phantom power.
Make sure you use a mono jack connector and cable
whenever the 9 V phantom power is not required.
aux in Auxiliary stereo input, e.g. for CD
3.5 mm stereo jack socket
Nom. input voltage:
Min. input voltage,
stereo:
mono:
Max. input voltage:
Input impedance:
Signal/noise ratio (A-weighted):
Equivalent input noise
(A-weighted):
mic in Balanced microphone input
Combo socket, XLR + jack ¼" (6.35 mm)
XLR (balanced), stereo jack (balanced), or mono jack
(unbalanced)
1 / sleeve = ground,
2 / tip = positive (+),
3 / ring = negative (–)
Nom. input voltage:
Min. input voltage:
Max. input voltage:
Input impedance (balanced):
Input impedance (unbalanced):
Voice filter:
Signal/noise ratio (A-weighted)
Equivalent input noise voltage
(A-weighted):
Phantom power (XLR only):
Supply resistors:
Load current:
clip indicator Headroom:
line out Preamplifier output after tone controls
and master
Mono jack, ¼" (6.35 mm)
Nom. output voltage:
Output impedance:
Min. load impedance:
Residual noise voltage
A-weighted):
pre out Preamplifier output before tone
controls and master
Mono jack, ¼" (6.35 mm)
Nom. output voltage:
Output impedance:
Min. load impedance:
bass
Influence at 100 Hz
treble
Influence at 10 kHz
Power amp
construction Monolith IC with DMOS output
rating Output power (THD = 1%)
Continuous output power is determined by the
limiter, see limiter threshold
500 mV (–6 dBV)
200 mV (–14 dBV)
9 V (+19 dBV)
25 µV (–92 dBV)
500 mV (–6 dBV)
100 mV (–20 dBV)
200 mV (–14 dBV)
10 V (+20 dBV)
> 22 kΩ
24 µV (–93 dBV)
10 mV (–40 dBV)
2 mV (–54 dBV)
1 V (0 dBV)
–11 dB at 300 Hz (referred to 10 kHz)
1.9 µV (–114 dBV)
6.8 kΩ
max. 10 mA
approx. 6 dB
1 V (0 dBV)
4 µV (–108 dBV)
500 mV (–6 dBV)
± 8 dB
±11 dB
60 W / 4 Ω
General
distortion
noise
20 kΩ
86 dB
signal processing
limiter
speaker system
power supply
mains fuse
operating temperature range
cooling fan
cabinet
87 dB
finish
dimensions
weight
Options
Voice filter of mic input can be bypassed by an internal jumper.
Refer modification to qualified personnel.
Definitions
1 kΩ
Rated conditions:
3 kΩ
• nominal input voltage at input under test
• input control adjusted to nominal output voltage at pre out.
74 dB
• gain of unused inputs fully anticlockwise
• master fully clockwise
• bass / treble centered
48 V
Nominal input voltage: Standard condition for specifications,
if not stated otherwise.
Minimum input voltage: Input voltage required for nominal output with
maximum gain and volume settings.
Maximum input voltage: Input voltage that does not cause distortion
more than rated THD+N, suitable control settings provided.
Nominal output voltage or power refers to rated conditions.
47 Ω
THD + N: Total harmonic distortion + noise, input voltage reduced by 10
2 kΩ
dB after setting up rated conditions.
Signal / noise ratio: Ratio of output voltage at rated conditions to output
noise voltage with input shorted.
Equivalent input noise voltage: Noise voltage at loudspeaker terminals di-
vided by gain of amplifier. Input shorted after setting up rated conditions.
Residual noise: Output noise with minimal gain and volume settings.
47 Ω
Adaptive limiter: Adaptive with respect to power supply. Maintains cons-
5 kΩ
tant headroom regardless of power supply fluctuations.
General: Signal voltages are RMS values. Test signal sine 1 kHz sine unless
stated otherwise. Noise measured from 20 Hz to 20 kHz. Noise stated for
a specific input implies that all other inputs are not used. Sound pressure
level (SPL) based on loudspeaker specification by manufacturer.
Specifications and appearance subject to change without notice.
TD20170608 (AG 8/3)
THD + N
Measured at loudspeaker terminals
Residual noise (A-weighted), referred to
nom. output power:
Acoustical: approx. 14 dB SPL / 1 m
Signal/noise ratio:
Subsonic filter, adaptive peak limiter,
speaker eq with harmonics exciter
Threshold
8" (200 mm) dual cone full-range speaker in bass
reflex cabinet
mains voltage (depending on model)
100, 120, 220, 230, or 240 V~, 50–60 Hz
Power consumption: max. 120 W
Size: 5 x 20 mm
220, 230, 240 V models:
100 and 120 V models:
Temperature controlled
15 mm (0.59") birch plywood
Waterbased acrylic, black spatter finish
Height
Width
Depth
Weight
< 0.1% (6 W / 4 Ω)
–97 dB
see input specs
50 W / 4 Ω
T 1A L 250V
T 2A L 250V
0...35 °C
269 mm (10.59")
335 mm (13.19")
260 mm (10.24")
7.5 kg (16.53 lbs)
13