Functional Description; Operation; Maintenance - Makita HM1304B Betriebsanleitung

FUNCTIONAL DESCRIPTION

CAUTION:
• Always be sure that the tool is switched off and unplugged
before adjusting or checking function on the tool.
Switch action (Fig. 1)
CAUTION:
• Before plugging in the tool, always check to see that
the switch trigger actuates properly and returns to the
"OFF" position when released.
To start the tool, simply pull the switch trigger. Release
the switch trigger to stop.
For continuous operation, pull the switch trigger and then
push in the lock button.
To stop the tool from the locked position, pull the switch
trigger fully, then release it.
ASSEMBLY
CAUTION:
• Always be sure that the tool is switched off and
unplugged before carrying out any work on the tool.
Side handle (auxiliary handle) (Fig. 2)
The side handle can be either freely swiveled or secured
at one position for use during tool operation. Just loosen
the nut to swivel the handle freely.
To secure the handle at a fixed position, first loosen the
nut and swing the handle to the desired position for use.
Then tighten the nut firmly. If the set bolt turns together
with the nut when you secure the nut, see that the pro-
jecting portion of the side handle fits into the notch on the
head of the set bolt.
Installing or removing the bit (Fig. 3)
This tool accepts bits either with or without a collar on its
shank.
To install the bit, follow either procedure (1) or (2)
described below.
(1) For bits with a collar (Fig. 4)
Pivot the tool retainer back and slightly downward.
Insert the bit into the tool holder as far as it will go.
To securely retain the bit, return the tool retainer to its
original position.
CAUTION:
• Always assure that the bit is securely retained by
attempting to pull the bit out of the tool holder after
completing the above procedure.
(2) For bits without a collar (Fig. 5)
Pivot the tool retainer back and slightly downward.
With the notched portion of the bit facing the tool retainer
shaft, insert the bit into the tool holder as far as it will go.
Then pivot the tool retainer further downward toward the
barrel to securely retain the bit.
CAUTION:
• Always assure that the bit is securely retained by
attempting to pull the bit out of the tool holder after
completing the above procedure.
• The bit without a collar cannot be retained by the
method shown in Fig. 4.
To remove the bit, follow the installation procedure in
reverse.

OPERATION

Chipping/Scaling/Demolition
Hold the tool firmly with both hands. Turn the tool on and
apply slight pressure on the tool so that the tool will not
bounce around, uncontrolled. Pressing very hard on the
tool will not increase the efficiency.

MAINTENANCE

CAUTION:
• Always be sure that the tool is switched off and
unplugged before attempting to perform inspection or
maintenance.
• Never use gasoline, benzine, thinner, alcohol or the
like. Discoloration, deformation or cracks may result.
Replacing carbon brushes (Fig. 6, 7 & 8)
When the resin insulating tip inside the carbon brush is
exposed to contact the commutator, it will automatically
shut off the motor. When this occurs, both carbon
brushes should be replaced. Keep the carbon brushes
clean and free to slip in the holders. Both carbon brushes
should be replaced at the same time. Use only identical
carbon brushes.
Use a screwdriver to remove the holder cap plates.
Use a screwdriver to remove the brush holder caps. Take
out the worn carbon brushes, insert the new ones and
secure the brush holder caps.
Reinstall the holder cap plates firmly.
Lubrication (Fig. 9 & 10)
This tool requires no hourly or daily lubrication because it
has a grease-packed lubrication system. It should be
relubricated after every 6 months of operation. Send the
complete tool to Makita Authorized or Factory Service
Center for this lubrication service. However, if circum-
stances require that you should lubricate it by yourself,
proceed as follows.
Run the tool for several minutes to warm it up. Switch off
and unplug the tool.
Remove the crank cap using a hex wrench, then replen-
ish with fresh grease (60 g). Use only Makita genuine
hammer grease (optional accessory). Filling with more
than the specified amount of grease (approx. 60 g) can
cause faulty hammering action or tool failure. Fill only
with the specified amount of grease.
Reinstall the crank cap securely with the hex wrench.
To maintain product SAFETY and RELIABILITY, repairs,
any other maintenance or adjustment should be per-
formed by Makita Authorized Service Centers, always
using Makita replacement parts.
5