Herunterladen Inhalt Inhalt Diese Seite drucken

Specifications; Additional Safety Rules For Tool - Makita HR4500C Betriebsanleitung

Vorschau ausblenden Andere Handbücher für HR4500C:
Inhaltsverzeichnis

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 12
ENGLISH
1 Bit grease
2 Bit shank
3 Bit
4 Chuck cover
5 Lock button
6 Change lever
7 Pointer
8 Side handle
9 Can be swung 360° on the
vertical and secured at any
desired position

SPECIFICATIONS

Model
Capacities
Tungsten-carbide tipped bit ........................ 45 mm
Core bit ..................................................... 125 mm
–1
No load speed (min
) .............................. 120 – 240
Blows per minute ................................ 1,250 – 2,550
Overall length ............................................... 488 mm
Net weight ....................................................... 7.8 kg
• Due to our continuing program of research and
development, the specifications herein are subject
to change without notice.
• Note: Specifications may differ from country to
country.
Power supply
The tool should be connected only to a power supply
of the same voltage as indicated on the nameplate,
and can only be operated on single-phase AC supply.
They are double-insulated in accordance with Euro-
pean Standard and can, therefore, also be used from
sockets without earth wire.
Safety hints
For your own safety, please refer to the enclosed
safety instructions.
6
Explanation of general view
10 Secures at eight different
positions back and forth
on the horizontal
11 Clamp nut
12 Loosen
13 Tighten
14 Side grip
15 Switch trigger
16 Adjusting dial
17 Clamp screw
18 Depth gauge
19 Power-ON indicator lamp
(green)
ADDITIONAL SAFETY RULES FOR
HR4500C
TOOL
1. Hold tools by insulated gripping surfaces
2. Wear ear protectors when using the tool for
3. Wear a hard hat (safety helmet), safety glasses
4. Be sure the bit is secured in place before
5. Under normal operation, the tool is designed
6. In cold weather or when the tool has not been
7. Always be sure you have a firm footing.
8. Hold the tool firmly with both hands.
9. Keep hands away from moving parts.
10. Do not leave the tool running. Operate the tool
11. Do not point the tool at any one in the area
12. Do not touch the bit or parts close to the bit
SAVE THESE INSTRUCTIONS.
20 Service indicator lamp (red)
21 Screwdriver
22 Brush holder cover
23 Brush holder cap
24 Screws
25 Connector
26 Black
27 White
28 Crank cap
29 Hex wrench
30 Hammer grease
31 To handle
when performing an operation where the cut-
ting tool may contact hidden wiring or its own
cord. Contact with a ''live'' wire will make
exposed metal parts of the tool ''live'' and
shock the operator.
extended periods. Prolonged exposure to high
intensity noise can cause hearing loss.
and/or face shield. It is also highly recom-
mended that you wear a dust mask and thickly
padded gloves.
operation.
to produce vibration. The screws can come
loose easily, causing a breakdown or accident.
Check tightness of screws carefully before
operation.
used for a long time, let the tool warm up for a
while by operating it under no load. This will
loosen up the lubrication. Without proper
warm-up, hammering operation is difficult.
Be sure no one is below when using the tool in
high locations.
only when hand-held.
when operating. The bit could fly out and
injure someone seriously.
immediately after operation; they may be
extremely hot and could burn your skin.
ENB010-1

Quicklinks ausblenden:

Werbung

Inhaltsverzeichnis
loading

Inhaltsverzeichnis