Technical Data; Before Starting The Equipment - EINHELL TP-CW 18 Li BL-Solo Originalbetriebsanleitung

4. Technical data

Motor power supply: ............................... 18 V DC
Idling speed: .....................................0-2900 min
Blow rate: .........................................0-3000 min
Clockwise/counter-clockwise: ........................Yes
Tool chuck: ..................................... ½" (12.7 mm)
Weight: .......................................................1.2 kg
Danger!
Sound and vibration
Sound and vibration values were measured in
accordance with EN 62841.
L sound pressure level ..................... 93.4 dB(A)
pA
K uncertainty ............................................. 3 dB
pA
L sound power level ...................... 104.4 dB(A)
WA
K uncertainty ............................................. 3 dB
WA
Wear ear-muff s.
The impact of noise can cause damage to hea-
ring.
Total vibration values (vector sum of three direc-
tions) determined in accordance with EN 62841.
Tightening screws and nuts of maximum per-
mitted size
Vibration emission value a
K uncertainty = 1.5 m/s
The stated vibration emission levels and stated
noise emission values were measured in ac-
cordance with a set of standardized criteria and
can be used to compare one power tool with
another.
The stated vibration emission levels and stated
noise emission values can also be used to make
an initial assessment of exposure.
Warning:
The vibration and noise emission levels may vary
from the level specifi ed during actual use, depen-
ding on the way in which the power tool is used,
especially the type of workpiece it is used for.
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
Anl_TP_CW_18_Li_Brushless_SPK13.indb 16 Anl_TP_CW_18_Li_Brushless_SPK13.indb 16
GB
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
-1
•
Wear protective gloves.
-1
Caution!
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment's construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.
3. Health damage caused by hand-arm vib-
rations if the equipment is used over a pro-
longed period or is not properly guided and
maintained.
Limit the operating time.
All stages of the operating cycle must be conside-
red (for example, times in which the electric tools
are switched off and times in which the tool is
switched on but operates without load).

5. Before starting the equipment

= 8.525 m/s
2
h
2
Be sure to read the following information before
you put the cordless screwdriver into operation:
1. Use only drive socket inserts which are suita-
ble for the purpose and in faultless condition.
2. Before you begin to screw in walls and ma-
sonry, check for concealed electric wiring,
gas pipes and water pipes.
6. Operation
6.1 Charging the Li battery pack (Fig. 2-3)
1. Remove the battery pack (5) from the handle,
pressing the pushlock button (8) downwards
to do so.
2. Check that your mains voltage is the same as
that marked on the rating plate of the battery
charger. Insert the power plug of the charger
(6) into the mains socket outlet. The green
LED will then begin to fl ash.
3. Push the battery pack onto the battery char-
ger.
- 16 -
09.09.2021 08:28:21 09.09.2021 08:28:21