Intended Use - Ryobi EAG750RS Anleitung

taking proper precautions as given below.
a) Maintain a firm grip on the power tool and position
your body and arm to allow you to resist kickback
forces. Always use auxiliary handle, if provided, for
maximum control over kickback or torque reaction
during start-up. The operator can control torque
reactions or kickback forces, if proper precautions are
taken.
b) Never place your hand near the rotating accessory.
Accessory may kickback over your hand.
c) Do not position your body in the area where power
tool will move if kickback occurs. Kickback will
propel the tool in direction opposite to the wheel's
movement at the point of snagging.
d) Use special care when working corners, sharp
edges, etc. Avoid bouncing and snagging the
accessory. Corners, sharp edges or bouncing have a
tendency to snag the rotating accessory and cause loss
of control or kickback.
e) Do not attach a saw chain woodcarving blade or
toothed saw blade. Such blades create frequent
kickback and loss of control.
ADDITIONAL SAFETY INSTRUCTIONS FOR
GRINDING OPERATIONS
SAFETY WARNINGS SPECIFIC FOR GRINDING OP-
ERATIONS:
a) Use only wheel types that are recommended for
your power tool and the specific guard designed
for the selected wheel. Wheels for which the power
tool was not designed cannot be adequately guarded
and are unsafe.
b) The grinding surface of centre depressed wheels
must be mounted below the plane of the guard lip.
An improperly mounted wheel that projects through the
plane of the guard lip cannot be adequately protected.
c) The guard must be securely attached to the power
tool and positioned for maximum safety, so the
least amount of wheel is exposed towards the
operator. The guard helps to protect the operator from
broken wheel fragments, accidental contact with wheel
and sparks that could ignite clothing.
d) Wheels must be used only for recommended
applications. For example, do not grind with the
side of cut-off wheel. Abrasive cut-off wheels are
intended for peripheral grinding, side forces applied to
these wheels may cause them to shatter.
e) Always use undamaged wheel flanges that are of
correct size and shape for your selected wheel.
Proper wheel flanges support the wheel, thus reducing
the possibility of wheel breakage. Flanges for cut-off
wheels may be different from grinding wheel flanges.
f) Do not use worn down wheels from larger power
tools. Wheels intended for a larger power tool are not
suitable for the higher speed of a smaller tool and may
burst.
2
All manuals and user guides at all-guides.com
ANGLE GRINDER SAFETY WARNINGS
a) Check that the speed marked on the grinding wheel is
b) Ensure that the dimensions of the grinding wheel are
c) Grinding wheels must be stored in a dry place.
d) Do not store objects on top of the grinding wheels.
e) Grinding wheels must not be used for any operation
f) Grinding wheels must be stored and handled with care
g) Inspect the grinding wheel before use to ensure that it is
h) Ensure that the wheel is fitted in accordance with this
i)
j)
k) Check that the workpiece is properly supported.
l)
m) Ensure that sparks resulting from use do not create
n) Always use protective safety glasses and ear
o) Use other personal protective equipment such as
p) Never place the tool on the floor or other surfaces while
q) The flange and clamp nut must have the same outer
r) Use the tool only for approved applications. Never use
s) Grip the tool securely with both hands while operating.

INTENDED USE

Grinding metals
Use the tool only for approved applications. Use of the
power tool for operations different from intended could
result in a hazardous situation.
equal to or greater than the rated speed of the tool.
compatible with the tool and that the wheel fits the
spindle.
other than grinding.
in accordance with the manufacturer's instruction.
not chipped or cracked. Chips or cracks can cause the
wheels to shatter, resulting in possible serious injury.
manual.
Ensure that the grinding wheel is correctly mounted and
tightened before use and run the tool at no-load speed
for 30 seconds in a safe position. Stop immediately if
there is considerable vibration or if other defects are
detected. If this condition occurs, check the tool to
determine the cause.
Do not use separate reducing bushings or adapters to
adapt large hole grinding wheels.
Use only grinding wheels approved by RYOBI.
a hazard, e.g., do not hit people, or ignite flammable
substances.
protectors.
gloves, apron and helmet when necessary.
it is running. Grinding wheels continue to rotate after
the tool is switched off. Never touch the wheel or place
it on the floor or other surfaces while it is rotating.
diameter.
coolants or water or use the tool as a fixed tool.
English