Black & Decker KR650 Handbuch Seite 24

ENGLISH
• The forward/reverse switch controls the direction of
rotation when your drill is used as a screwdriver, or
when clearing a jammed drill bit.
• The adjustable depth stop gives precise control of
the hole depth, when you drill blind holes.
FITTING THE DRILL BIT (KEYLESS CHUCKS)
Proceed as follows:
Disconnect the plug from the electricity supply.
chuck firmly to securely grip the drill bit.
FITTING THE DRILL BIT (KEYED CHUCKS)
Proceed as follows:
Disconnect the plug from the electricity supply.
chuck key in one of the three holes in the body of the
chuck, ensuring the head of the chuck key is engaged
with the barrel of the chuck. Turn the chuck key
clockwise to tighten the jaws and securely grip the drill
bit. Remove the chuck key.
REMOVING THE CHUCK (KEYLESS CHUCKS)
Proceed as follows:
To remove the chuck, open the jaws, hold it firmly in
one hand and with a screwdriver held in the other hand,
turn the set-screw in the chuck clockwise
approximately one turn, to loosen it.
24
KR580-700 ML p21-35
While pressing
P P P P P P P P @ P @ P @ P P @ P P P @ P P P @ P P P @ P P P @ P P @ P @ @ @ P @ @ @ P @ @ @ P P @ @ P @ @ @ P @ @ @ P @ @ @ P @ @ @ P @ @ y @ @
the spindle lock,
rotate the chuck
until the jaws are
sufficiently open.
Insert the drill bit
in the jaws of the
chuck and
tighten. Twist the
Rotate the barrel
of the chuck until
the jaws are
sufficiently open.
Insert the drill bit
in the jaws of the
chuck. Insert the
chuck key with
the end of the
Place an allen
key in the chuck
and tighten the
jaws. Give the
allen key a short
powerful blow in
an anti-clockwise
direction with a
24
hammer to loosen the chuck on the spindle. Remove
the allen key. Use the screwdriver to turn the set-
screw clockwise until it totally disengages from the
spindle. Remove the chuck from the spindle by rotating
it anti-clockwise. To fasten the chuck, put it on the
thread and turn it clockwise until it stops. Put in the
screw and turn it anti-clockwise until absolutely firm.
REMOVING THE CHUCK (KEYED CHUCKS)
the chuck clockwise with the other hand until it comes
out. Use only the correct chuck key. Place the chuck
key into the chuck, and hold the drill firmly in one hand
with the chuck pointing away from you. Rotate the
chuck so that the chuck key is just above the horizontal
position on the right hand side of the machine. Give the
crossbar end of the key a sharp downward blow with a
mallet or light hammer. The chuck should now be
yy@ @ y y @ @ @ @ @ @ @ @ @ @ @ @ @ @ P P @ @ P P @ @ @ @ P P P P @ @ P P @ @ @ @ P P P P P P @ @ P P P P P P @ @ P P P P P P @ @ P P P P P P @ @ P P @ @ P P @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ @ P P P P @ @ P P @ @ P P @ @ @ @ P P P P P P @ @ P P P P P P @ @ P P P P P P @ @ P P P P P P @ @ P P
sufficiently loose to be unscrewed by hand.
FITTING THE SIDE HANDLE
PP @@ PP PP PP @@ PP @@ PP @@ PP @@ PP @@ PP @@ PP @@ PP @@ PP @@ PP @@ PP @@ PP @@ PP @@ PP @@ PP @@ @@ PP PP @@ @@ PP @@ PP @@ PP @@ PP @@ PP @@ PP @@ PP @@ PP @@ PP @@ PP @@ PP @@ PP @@ PP PP @@ @@ PP PP @@ @@ @@
y P @ P @ P @ P @ P @ P @ P @ P @ P @ P @ P @ P @ P @ P @ P @ P @ P P P P P P @ P @ P @ P @ P @ P @ P @ P @ P @ P @ P @ P @ P @ P @ @ @ P @ @ @ @
turning clockwise.
SETTING THE ADJUSTABLE DEPTH STOP
Proceed as follows:
P @ P @ @ @ @ @ @ @ P P @ P @ P P @ P P P @ P P P y @ @ @ @ @ P P @ P P @ @ P @ P @ P @ P P P @ @ P @ P @ @ P @ @ P P @ P @ P P @ @ P @ @ P P @ P @ P P P @ @ P P @ @ P P @ @ @ @ P P @ @ P P @ @ P P y y P P @ @ P P P P P P P P P P P P @ @ P P @ @ P P P P @ @ P P P P @ @ P P P P P P @ @ P P P P P P @ @ P P P P P P @ @ P P P P @ @ @ @ @ @ P P @ @ @ @ @ @ P P @ @ @ @ @ @ P P @ @ @ @ @ @ P P @ @ @ @ @ @ P P @ @ @ @ @ @ P P @ @ @ @ @ @ P P
Fit the drill bit. Loosen the side handle.
@@ yy PP @@ @@ PP @@ PP @@ PP @@ PP @@ PP @@ PP @@ PP @@ PP @@ PP @@ PP @@ PP @@ PP @@ PP @@ PP @@ PP @@ PP @@ PP @@ PP @@ PP @@ PP @@ PP @@ PP @@ PP @@ PP @@ PP @@ PP @@ PP @@ PP @@ PP @@ PP @@ @@ @@ PP @@ PP PP PP PP
PP PP PP @@ PP @@ PP @@ PP @@ PP @@ PP @@ PP @@ PP @@ PP @@ PP @@ PP @@ PP @@ PP @@ PP @@ PP @@ PP @@ PP @@ PP @@ PP @@ PP @@ PP @@ PP @@ PP @@ PP @@ PP @@ PP @@ PP @@ PP @@ PP @@ PP @@ PP @@ PP @@ PP @@ @@ @@ yy PP @@
05-02-2001, 10:48
To remove the
chuck, open the
jaws of the chuck
with the chuck
key. Hold the
chuck firmly in one
hand, and with a
screwdriver turn
the set screw in
Loosely locate
the handle on the
body of your drill.
Rotate the handle
around the body
of your drill until it
is in the desired
position. Tighten
the handle by
Slide the depth
stop until the end
of the depth stop
aligns with the
end of the drill bit.
Slide the depth
stop until the
distance between
the end of the