Maintenance - AEG PNEUMATIC 3000 SUPER X2 Gebrauchsanleitung

TECHNICAL DATA
Nominal power output .........................................................
Rated output ........................................................................
No-load speed
1st gear ............................................................................
2nd gear ...........................................................................
Speed under load max.
1st gear ............................................................................
2nd gear ...........................................................................
Rate of percussion under load max. ....................................
Single impact strength .........................................................
Drilling capacity in concrete .................................................
Drilling capacity in steel .......................................................
Drilling capacity in wood ......................................................
Light core cutter in bricks and limestone .............................
Chuck neck diameter ...........................................................
Weight without cable ...........................................................
Typical weighted acceleration in the hand-arm area ...........
Typical A-weighted sound levels:
Sound pressure level ...........................................................
Sound power level ...............................................................
Wear ear protectors!
Measured values determined according to EN 50 144.
SAFETY INSTRUCTIONS
Please pay attention to the safety instructions in the
attached leaflet!
Appliances used at many different locations including open
air must be connected via a current surge preventing switch.
Always wear goggles when using the machine. It is
recommended to wear gloves, sturdy non slipping shoes
and apron.
Sawdust and splinters must not be removed while the
machine is running.
Always disconnect the plug from the socket before carrying
out any work on the machine.
Only plug-in when machine is switched off.
Keep mains lead clear from working range of the machine.
Always lead the cable away behind you.
Always use the auxiliary handle, even if the machine has a
safety clutch since this safety clutch only engages when the
machine blocks with a jerk.
Do not use diamond core drills on hammer mode.
When working in walls ceiling, or floor, take care to avoid
electric cables and gas or waterpipes.
Always switch off hammer action when using chuck adaptor.
SPECIFIED CONDITIONS OF USE
The rotary pneumatic hammer can be used for hammer
drilling, chiselling in stone and drilling in wood, metal as well
as plastic.
Do not use this product in any other way as stated for
normal use.
EC-DECLARATION OF CONFORMITY
We declare under our sole responsibility that this product is
in conformity with the following standards or standardized
documents. EN 50144, EN 55014-1, EN 55014-2,
EN 61000-3-2, EN 61000-3-3, in accordance with the
regulations 98/37/EC, 89/336/EEC
Manager Product Development
19 ENGLISH
PN 3000 X
......... 600 W ............ 800 W ............... 600 W ................ 750 W ...............1010 W
......... 300 W ............ 400 W ............... 300 W ................ 375 W .................505 W
...... 0-970 min
............. – .......... 0-3260 min
......... 660 min
............. – ............. 2290 min
....... 3800 min
.......... 2,7 J ............... 3,0 J .................. 2,7 J ................... 2,8 J ....................3,1 J
........... 24 mm ........... 26 mm .............. 24 mm ............... 26 mm .................30 mm
........... 16 mm ........... 18 mm .............. 16 mm ................ 18 mm .................20 mm
........... 30 mm ........... 40 mm .............. 30 mm ................ 40 mm .................66 mm
........... 68 mm ........... 82 mm .............. 68 mm ................ 68 mm .................82 mm
........... 43 mm ........... 43 mm .............. 43 mm ................ 43 mm .................43 mm
.......... 2,7 kg ............. 3,3 kg ................ 3,3 kg ................. 3,3 kg ..................3,4 kg
............11 m/s
........... 87 dB (A) ....... 87 dB (A) .......... 87 dB (A) ........... 87 dB (A) ............96 dB (A)
......... 100 dB (A) ..... 100 dB (A) ........ 100 dB (A) ......... 100 dB (A) ..........109 dB (A)
Volker Siegle
PN 3000 X2 PN 3000 XN2
BH 625 FIXTEC
... 0-1050 min ........ 0-970 min
-1 -1
...... 0-3000 min
-1
........ 700 min ........... 660 min
-1 -1
......... 2100 min
-1
...... 4000 min ......... 3800 min
-1 -1
...........11 m/s ..............11 m/s
2 2
MAINS CONNECTION
Connect only to single-phase a.c. current and only to the
system voltage indicated on the rating plate. It is also
possible to connect to sockets without an earthing contact
as the design conforms to safety class II.
ELECTRONICS
Protection of motor in case of overload: Motor protection
device controlled by motor load. The machine will slowly
continue to run in order to cool the motor down. After
sufficient cooling machine can be restarted by switching off
and on again (only applicable for PN 3000 SUPER X2,
PN 3000 SUPER XN2, FIXTEC PLUS).
Under the effect of extreme electromagnetic interferences
from the outside, temporary variations in the speed of
rotation could arise in particular cases.

MAINTENANCE

Clean and lightly grease the FIXTEC-reception from time to
time.
The ventilation slots of the machine must be kept clear at all
times.
Important note! If the carbon brushes are worn, in addition
to exchanging the brushes the tool should be sent to after-
sales service. This will ensure long service life and top
performance.
Use only AEG accessories and spare parts. Should
components need to be exchanged which have not been
described, please contact one of our AEG service agents
(see our list of guarantee/service addresses).
If needed, an exploded view of the tool can be ordered.
Please state the ten-digit No. as well as the machine type
printed on the label and order the drawing at your local
service agents or directly at: AEG Elektrowerkzeuge,
Max-Eyth-Straße 10, D-71364 Winnenden, Germany.
SYMBOLS
Always disconnect the plug from the socket
before carrying out any work on the machine.
Accessory - Not included in standard
equipment, available as an accessory.
PN 3000 SUP XN2 PN 3000 SUP X2
FIXTEC PLUS
......... 0-850 min ..........0-970 min
-1 -1
....... 0-2700 min ........0-3000 min
-1 -1
............ 670 min .............680 min
-1 -1
.......... 2150 min ...........2200 min
-1 -1
.......... 3900 min ...........4000 min
-1 -1
................11 m/s ................14 m/s
2 2
-1
-1
-1
-1
-1
2