Inhaltsverzeichnis
Werbung
Downloaded from
www.Manualslib.com
OBJ_BUCH-976-006.book Page 19 Thursday, July 24, 2014 8:36 AM
Technical Data
Angle Grinder
Article number
Rated power input
Output power
Rated speed
Grinding disc diameter, max.
Thread of grinder spindle
Thread length (max.) of grinder spindle
Reduced starting current
Weight according to EPTA-Procedure 01/2003 with
vibration-damping auxiliary handle
Weight according to EPTA-Procedure 01/2003 with
standard-auxiliary handle
Protection class
The values given are valid for a nominal voltage [U] of 230 V. For different voltages and models for specific countries, these values can vary.
Only for power tools without reduced starting current: Starting cycles generate brief voltage drops. Interference with other equipment/machines may
occur in case of unfavourable mains system conditions. Malfunctions are not to be expected for system impedances below 0.25 ohm.
Noise/Vibration Information
Sound emission values determined according to
EN 60745-2-3.
Typically the A-weighted noise levels of the product are:
Sound pressure level 92 dB(A); Sound power level
103 dB(A). Uncertainty K =3 dB.
Wear hearing protection!
Vibration total values a
(triax vector sum) and uncertainty K
h
determined according to EN 60745:
2
Surface grinding: a
=7.5 m/s
, K=1.5 m/s
h
2
2
Disk sanding: a
=4.0 m/s
, K=1.5 m/s
.
h
The vibration level given in this information sheet has been
measured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with anoth-
er. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or insertion tools or is
poorly maintained, the vibration emission may differ. This
may significantly increase the exposure level over the total
working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working
period.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work pat-
terns.
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under "Technical Data" is in conformity with all rele-
vant provisions of the directives 2011/65/EU, 2014/30/EU,
Bosch Power Tools
manuals search engine
PWS 20-230
3 603 C59 W..
W
2000
W
1250
-1
min
6600
mm
230
M 14
mm
25
–
kg
5.5
kg
5.4
/II
2006/42/EC including their amendments and complies with
the following standards: EN 60745-1, EN 60745-2-3.
Technical file (2006/42/EC) at:
Robert Bosch GmbH, PT/ETM9,
70764 Leinfelden-Echterdingen, GERMANY
Henk Becker
Executive Vice President
Engineering
2
,
Robert Bosch GmbH, Power Tools Division
70764 Leinfelden-Echterdingen, GERMANY
Leinfelden, 04.06.2014
Assembly
Mounting the Protective Devices
Before any work on the machine itself, pull the mains
plug.
Note: After breakage of the grinding disc during operation or
damage to the holding fixtures on the protection guard/power
tool, the machine must promptly be sent to an after-sales ser-
vice agent for maintenance. For addresses, see section "Af-
ter-sales Service and Application Service".
Protection Guard for Grinding
Place the protection guard 5 on the spindle collar. Adjust the
position of the protection guard 5 to the requirements of the
operation and lock the protection guard 5 with the locking
screw 6.
Adjust the protection guard 5 in such a manner that
sparking is prevented in the direction of the operator.
English | 19
PWS 20-230 J
PWS 1900
3 603 C59 V..
3 603 C59 W..
2000
1900
1250
1170
6600
6600
230
230
M 14
M 14
25
25
–
5.5
5.5
5.4
5.4
/II
/II
Helmut Heinzelmann
Head of Product Certification
PT/ETM9
1 609 92A 0RV | (24.7.14)
Werbung
Inhaltsverzeichnis
