Husqvarna DE 110i Bedienungsanweisung Seite 17

To connect the battery to the battery
charger
Note:
Charge the battery if it is the first time that you
use it. A new battery is only 30% charged.
1. Make sure that the battery is dry.
2. Put the battery in the battery charger. (Fig. 18)
3. Make sure that the green charging light on the
battery charger comes on. That means that the
battery is connected correctly to the battery charger.
(Fig. 19)
4. When all LEDs on the battery come on, the battery is
fully charged. (Fig. 20)
5. To disconnect the battery charger from the mains
socket, pull the plug. Do not pull the cable.
6. Remove the battery from the battery charger.
Note:
Refer to the battery and battery charger
manuals for more information.
To lock and unlock the transport
wheels
For operation on a surface with a slope it is necessary to
lock the transport wheels.
WARNING:
must be clean and without dust for safe
operations. Refer to
on page 19 .
1. Hold the product in a stationary and safe position.
2. Push down the wheel brake on each side to lock the
wheels. (Fig. 21)
Note:
DE110i has only 1 wheel brake.
3. Pull up the wheel brakes to unlock the wheels.
Functions of the control panel
The control panel controls and monitors important
functions and setups of the product. Refer to
on the control panel on page 23 to find solutions for the
warnings.
(Fig. 22)
1. The prefilter is clogged. Refer to
particles from the prefilter during operation on page
18 .
2. The HEPA filter is clogged, damaged or missing.
Warnings on the control panel on page 23 .
Refer to
Warnings on the control panel on
3. Warning. Refer to
page 23 .
®
4. Bluetooth connection. Refer to
connectivity with fleet on page 16 .
1618 - 004 - 24.01.2022
Wheels and bearings
Maintenance schedule
Warnings
To remove dust
To use embedded
5. Diameter change function for hose, refer to
the hose nozzle diameter on page 17
6. e-Flow button, refer to
7. On/Off button
e-Flow function
The product has an e-Flow function. This function
automatically adjusts the airflow to the workload for
optimal performance. The product always starts with the
last settings used.
Functions of the control panel on page 17 to
Refer to
engage or disengage the function.
Airflow warning system
The airflow in the suction hose must be more than 20
m/s (66 ft/s).
For the minimum airflow with the selected hose diameter
refer to the table.
DE 110
in.(mm) CFM (m
1 (27) 24 (41)
1 ¼ (32) 34 (58)
1 ½ (38) 48 (82)
1 ⅔ (42) 59 (100)
2 (51) 87 (147)
Note:
If the airflow is less than 20 m/s (66 ft/s), the
sound alarm and the warning symbol comes on. Refer to
Warnings on the control panel on page 23 .
To select the hose nozzle diameter
Note:
If you do not select the correct hose diameter,
the airflow warning system will come on.
When you start the product, the last selected hose
diameter is automatically selected.
• Push the button to select the correct hose diameter.
The green LED tells which diameter you have
selected. (Fig. 23)
To install and remove the battery
1. Put the battery in the battery holder. The electricity
symbol shows which holder is energized. (Fig. 24)
To select
e-Flow function on page 17
DE 120
3
/h) in.(mm) CFM (m
1 ½ (38) 48 (82)
1 ⅔ (42) 59 (100)
2 (51) 87 (147)
2 1/2 (63) 132 (224)
3 (76) 192 (327)
3
/h)
17