Laica PS4007 Anleitung Seite 15

GB
English
To get the best results from your scale, weight yourself twice, and if the two weights are different
from each other, your weight is between the two readings.
Wait for about 15 minutes after getting up, so that the water can distribute through around your
body.
• The surface of the scale can be slippery, if wet.
• Warning!
The measurement function of body fat and water percentage, may be utilized only by people
that belong to an age group that goes from 10 to 80 and that are between 100 and 240 cm
tall.
• The precision of this fat and water percentage measurement can be altered in the following
cases:
a) a high alcohol level
b) a high level of caffeine or drugs
c) after an intense sports activity
d) during an illness
e) during pregnancy
f) after heavy meals
g) in presence of dehydration problems
h) your personal data (height, age, sex) have not been input correctly
i) if you have wet or dirty feet
j) people with swollen legs
Warning!
The body fat and water percentage is to be considered only as approximate
information.
For any further information, please consult your doctor or dietician.
OPERATING INSTRUCTIONS
a. How to insert batteries
This scale operates with 4 replaceable 1.5 V alkaline batteries. When the batteries are dead the
display shows "LO" or the battery symbol. Insert new batteries with the positive pole upwards.
Remove the run down batteries by lifting the cover of the battery compartment located on the
bottom of the device. Extract the batteries and dispose them as special waste at the specific
collection points forecast for recycling. For more information about the disposal of run down
batteries, please contact either the store where the device containing the batteries was purchased,
or the Municipality, or the waste disposal local service.
Caution: For greater safety, children younger than 12 years should not remove
the batteries.
b. Unit of measure key
ELECTRONIC PERSONAL SCALE WITH INDICATOR OF % OF FAT AND % OF WATER
With the scale switched off, select the measuring unit (kg, lb or st) via the key on the bottom
of the scale.
c. Use as simple scale
1) Press "ON" button to turn the scale on.
2) Wait a few seconds and when "0.0" appears on the display screen, the scale is ready for
use.
3) Step onto the scale and wait without moving; after a few seconds, the display screen will
show your weight. Do not lean on anything while being weighed as this could alter the
reading.
4) Step off the scale, the display screen will continue to show your weight for a few seconds
then it will turn itself off automatically.
d. How to input personal data
This scale may memorize the data of 10 different persons.
1) Press the "SET" button.
2) "P1" will flash on the display screen, indicating the "01" person: if you wish to change the
memory location (memories from 0 to 9), press the "▲" or "▼" symbols. Once you have
selected the memory location, confirm by pressing "SET".
3) Continue by pressing the "▲" or "▼" symbols to define your sex. Confirm by pressing
"SET".
4) Use the "▲" or "▼" symbols again to insert age (from 10 to 80 ) and then confirm by
pressing "SET".
5) Insert your height (from 100 cm to 240 cm) using the "▲" or "▼" symbols to increase
or decrease the value. The display screen will give the value in cm or ft. Press SET to
confirm.
6) Now the scale has stored all your data; the display shows them to allow you checking their
correct entering.
At this point, the display shows "0.0". Get on the scale paying attention to position the naked
feet correctly on the two electrodes. Then, the display shows the following data
sequentially:
- your weight
- the message FAT (bodyfat) and the percentage of fat present in the body
- the message TBW (bodywater) and the percentage of water present in your body
Compare the obtained fat percentage (FAT) obtained with the parameters given in the "Bodyfat
table": if the values are not included in the normal range, refer to your doctor.
Estimate the water percentage (TBW) as in paragraph "% of water".
7) The scale switches off automatically after about 10 seconds.
To modify the entered data, call up the involved memory area and repeat the whole proceeding.
To enter the data of another person, select a free memory area and repeat the whole
14