Memory Function - Makita CW001G Gebrauchsanleitung

A) When the appliance get equal to or greater than
30° from level angle as shown A-1 in the figure,
the appliance shuts down and the temperature
display shows "F1" for a while. It takes 3 minutes
to restart after the appliance back in level position.
When the appliance get equal to or greater than
70° from level angle as shown A-2 in the figure,
the appliance shuts down and the temperature
display shows "F6" until restart. It takes 2 hours to
restart after the appliance back in level position.
► Fig.4
B) When the appliance get equal to or greater than
30° from level angle as shown B-1 in the figure,
the appliance shuts down and the temperature
display shows "F1" for a while. It takes 3 minutes
to restart after the appliance back in level position.
When the appliance get equal to or greater than
40° from level angle as shown B-2 in the figure,
the appliance shuts down and the temperature
display shows "F6" until restart. It takes 2 hours to
restart after the appliance back in level position.
► Fig.5
C) When the appliance get equal to or greater than
30° from level angle as shown C-1 in the figure,
the appliance shuts down and the temperature
display shows "F1" for a while. It takes 3 minutes
to restart after the appliance back in level position.
When the appliance get equal to or greater than
70° from level angle as shown C-2 in the figure,
the appliance shuts down and the temperature
display shows "F6" until restart. It takes 2 hours to
restart after the appliance back in level position.
► Fig.6
D) When the appliance get equal to or greater than
30° from level angle as shown D-1 in the figure,
the appliance shuts down and the temperature
display shows "F1" for a while. It takes 3 minutes
to restart after the appliance back in level position.
When the appliance get equal to or greater than
70° from level angle as shown D-2 in the figure,
the appliance shuts down and the temperature
display shows "F6" until restart. It takes 2 hours to
restart after the appliance back in level position.
► Fig.7
E) When the appliance turns 180° from level angle,
the appliance shuts down and the temperature
display shows "F6" until restart. It takes 2 hours to
restart after the appliance back in level position.
USB charging
There is the USB port in the battery compartment. The
USB port continuously outputs 5V voltage in operation
state.

Memory function

After setting the control temperature, if the user does
not operate within 5 seconds, the current setting will be
memorized. Next time, the appliance starts in the same
setting.
Switching the unit of temperature
You can switch the unit of temperature °C (degree
Celsius) or °F (degree Fahrenheit) by following
procedure.
1. Turn on the appliance.
2. Press the cool / heat switch button until the unit
(°C or °F) starts flashing.
3. Press the temperature plus button or the tempera-
ture reduction button to select unit.
4. Press the cool / heat switch button, or leave the
appliance 5 seconds without any operation. The
unit selection is completed.
Shoulder belt
CAUTION:
Make sure the shoulder belt
securely attached properly. Otherwise falling acci-
dent may occur.
1. Put the belt through left and right handles.
2. Buckle the belt.
► Fig.8
Error code
For the specific errors, the temperature display shows
following code.
Error code
F1 Tilt protection is active. Refer the section for
the tilt protection function.
F2 Running out of battery.
F3 Input voltage is low. Refer the paragraph for
the car input protection.
F4 Input voltage is high. Refer the paragraph for
the over-voltage protection.
F5 Something is wrong with the sensor in the
appliance. Take the appliance to Makita
Authorized or Factory Service Centers.
F6 Tilt protection is active.
Refer the section for the tilt protection function.
MAINTENANCE
CAUTION:
Always be sure that the appliance
is switched off, unplugged, and the battery car-
tridge is removed before attempting to perform
inspection or maintenance.
NOTICE:
Never use gasoline, benzine, thinner,
alcohol or the like. Discoloration, deformation or
cracks may result.
To maintain product SAFETY and RELIABILITY,
repairs, any other maintenance or adjustment should
be performed by Makita Authorized or Factory Service
Centers, always using Makita replacement parts.
Cleaning
• Clean the oil stain in the chamber regularly.
12 ENGLISH
Matter