Makita CW001G Gebrauchsanleitung Seite 10

1. Connecting the power supply
A) Battery
CAUTION:
Always switch off the tool before
installing or removing of the battery cartridge.
CAUTION:
Hold the appliance and the bat-
tery cartridge firmly when installing or removing
battery cartridge. Failure to hold the appliance and
the battery cartridge firmly may cause them to slip off
your hands and result in damage to the appliance and
battery cartridge and a personal injury.
CAUTION:
Be careful not to pinch your finger
when opening or closing the battery cover.
CAUTION:
Be careful not to pinch your fin-
gers between the battery cartridge and the termi-
nals. It may cause slash injury.
To install the battery cartridge, open the battery
cover.Align the tongue on the battery cartridge
with the groove in the housing and slip it into
place. Insert it all the way until it locks in place with
a little click.
Then close the battery cover.
To remove the battery cartridge, slide it from the
appliance while sliding the button on the front of
the cartridge.
► Fig.2 1. Red indicator 2. Button 3. Battery cartridge
CAUTION:
Always install the battery cartridge
fully until the red indicator cannot be seen. If not,
it may accidentally fall out of the appliance, causing
injury to you or someone around you.
CAUTION:
Do not install the battery cartridge
forcibly. If the cartridge does not slide in easily, it is
not being inserted correctly.
NOTE: Up to two battery cartridges can be installed,
although the appliance uses one battery cartridge for
operation.
B) AC adaptor (Only use for recre-
ational vehicle)
Optional accessory
When using the appliance with AC power, use the AC
adaptor supplied with the appliance. Insert the plug to
"DC IN" inlet of the appliance and then insert the other
end to an outlet.
When the appliance is operating with power from AC
adaptor, the lamp of "DC IN" lights up.
C) Cigarette lighter adaptor
When using the appliance with the cigarette lighter
socket, use the cigarette lighter adaptor supplied with
the appliance. Insert the plug to "DC IN" inlet of the
appliance and then insert the other end to the cigarette
lighter socket.
When the appliance is operating with power from ciga-
rette lighter adaptor, the lamp of "DC IN" lights up.
CAUTION:
Insert the plug completely into the
"DC IN" inlet. Failure to do so may deform the plug
or cause a fire.
CAUTION:
Always close the "DC IN" socket
cover firmly when the power cord is not plugged.
Otherwise foreign matter may enter the appliance and
cause a malfunction.
NOTICE:
[Only when operating with 18 V (LXT)
battery] When the appliance has been operated for
about 24 hours with the 18 V(LXT) battery cartridge
installed, battery cartridge may shut down its own
power to protect the battery cartridge. In this case,
the appliance can not operate with the battery
power supply and the battery indicator also goes
off. To resume the battery power supply, remove
and re-install the battery cartridge.
NOTE: When the appliance shifts power supply, the
compressor will stop for about 3 minutes to protect the
compressor.
NOTE: After turning off the appliance, it takes about 3
minutes to restart the compressor because of the pro-
tection of the compressor.
2. Turning on the appliance
Press the power button to turn on the appliance. Press
the power button again to turn off the appliance.
3. Switching cooling / heating mode
Press the cool / heat switch button to switch the oper-
ating mode.
• When the appliance operates in cooling mode, the
lamp of cooling mode lights up.
• When the appliance operates in heating mode, the
lamp of heating mode lights up.
The temperature display flashes the control temperature.
4. Selecting the control temperature
Press the temperature plus button or the temperature
reduction button to select the control temperature. Refer
the chapter "SPECIFICATIONS" for the selectable
control temperature.
The appliance starts cooling / heating 5 seconds after
without any operation, then the control temperature stop
flashing and the temperature display shows the current
temperature.
The appliance stops cooling / heating when the current
temperature reaches the control temperature.
Tips for efficient cooling
• Opening the upper cover for long periods can
cause significant increase of the temperature in
the chamber.
• Regularly clean surfaces that can come in contact
with food and accessible drainage systems.
• Store raw meat and fish in suitable containers in
the chamber, so that it is not in contact with or drip
onto other food.
• If the chamber is left empty for long periods:
10 ENGLISH