PHM-802 C
•
The expected level can be modified for each amplifier:
-
Level of pilotton directly on the item via keybord or
with software on PC.
•
The pilotton is only active during the messurement and
only on the tested amplifier (no permanent tone!)
•
Time for messasurement of all amplifiers approx. 10s (for
10 amplifiers)
•
Automatical switch of the 1st faulty amplifier to backup-
amplifier (signal-and speakers)
•
A faulty amplifier is monitored ongoing and switched
back automatically if the failure could be fixed by it self
(„selfhealing")
•
Display of the status of voltage input (a faulty input sho-
wes -)
•
Available adjustments with autarc mode (without Bus-
connection):
-
Temporally deactivating of monitoring (for service-
needs)
-
Fixing the monitoringintervall in 5 steps from 15s to 90s
-
Amplifier activating/deactivating
-
Regulation of the expected level for every amplifier
with optical/accousical levelcontrol
-
Regulation of the messurement-frequenzy from 19 to
25 kHz in 13 steps (additional testsignal 1 KhZ to be
regulated temporally)
-
Activating the failure-input
-
Controlfunction of the backup-relais
-
Choosing the language
-
Choosing the LCD-contrast
-
Showing the firmwarerevision/starting the item new
•
Additional functions with optional Bus-module for con-
nection of the VARES-3000 Bus:
-
Comfortable configuration of the item by using Con-
figV3000
-
External monitoring of all incoming signallines (in
connection with PSS-224 C)
-
Use of all possibilities for configuration:
-
Saving all settingdata and the possibility to name
all amplifiers and the tool for monitoring the failu-
reinputs by using ConfigV3000
-
Ability to program the failureinput as opener or
closer
-
Ability to regulate the monitoringinterval finer
(5 sec.)
All manuals and user guides at all-guides.com
UNIVERSAL AMPLIFIER MONITORING
•
Der Messpegel ist für jeden Verstärker einzeln anpassbar:
-
Pegel des Pilottons direkt am Gerät per Tastatur oder
per Software am PC.
•
Der Pilotton ist nur während der Messung und nur auf
der zu prüfenden Endstufe aktiv (kein Dauerton!).
•
Dauer der Messung aller Endstufen ca. 10s (bei 10 End-
stufen).
•
Automatische Umschaltung der 1. defekten Endstufe auf
die Havarieendstufe (Signal- und Lautsprecherseitig).
•
Eine defekte Endstufe wird weiter überwacht, automa-
tische Rückstellung der Umschaltung, wenn Fehler be-
hoben wird („Selbstheilung").
•
Anzeige des Zustands der Spannungseingänge (ein de-
fekter Eingang zeigt - ).
•
Einstellmöglichkeiten bei autarkem Betrieb (ohne Busan-
bindung):
-
temporäre Deaktivierung der Überwachung (zu Ser-
vicezwecken)
-
Einstellen des Überwachngsintervalls in 5 Stufen von
15s bis 90s
-
Verstärker aktivieren/deaktivieren
-
Einstellen des Messpegels für jeden Verstärker mit
optisch/akustischer Pegelkontrolle
-
Einstellen der Messfrequenz von 19 bis 25kHz in 13
Stufen (zusätzlich Prüfsignal 1kHz temporär einstellbar)
-
Aktivieren des Fehlereingangs
-
Funktionskontrolle der Havarierelais
-
Einstellen der Sprache
-
Einstellen des LCD-Kontrasts
-
Firmwarerevision anzeigen / Gerät neustarten
•
Zusätzliche Funktionen mit optionalem Busmodul zur
Anbindung an den VARES-3000 Bus:
-
Komfortable Konfiguration des Gerätes vom Con-
figV3000 aus
-
Externe Überwachung der ankommenden Signallei-
tungen (in Verbindung mit PSS-224 C)
-
Nutzung aller Konfigurationsmöglichkeiten:
-
Speicherung der Einstelldaten und Bennungs-
möglichkeit aller Verstärker und des Fehlerein-
gangs im ConfigV3000
-
Programmierung des Fehlereingangs als Öffner
oder Schließer möglich
-
Feinstufigere Einstellung des Überwachungsinter-
valls (5 Sek.)
7