Kärcher NT 27/1 Originalbetriebsanleitung Seite 9

Please read and comply with these origi-
nal instructions prior to the initial opera-
tion of your appliance and store them for
later use or subsequent owners.
– Before first start-up it is definitely necessary to read
the safety indications Nr. 5.956-249.0!
– The non-compliance of the operating and safety in-
structions may lead to damages of the appliance
and to dangers for the operator and other persons.
– In case of transport damage inform vendor immedi-
ately.
– When unpacking the product, make sure that no
accessories are missing and that none of the pack-
age contents have been damaged.
Contents
Environmental protection
Proper use
Device elements
Start up
Operation
Transport
Storage
Care and maintenance
Troubleshooting
Warranty
Accessories and Spare Parts
EU Declaration of Conformity
Declaration of Conformity (UK)
Technical specifications
Environmental protection
The packaging material can be recycled.
Please do not throw the packaging mate-
rial into household waste; please send it
for recycling.
Old appliances contain valuable materi-
als that can be recycled; these should be
sent for recycling. Batteries, oil, and sim-
ilar substances must not enter the envi-
ronment. Please dispose of your old ap-
pliances using appropriate collection sys-
tems.
Electrical and electronic devices often contain compo-
nents which could potentially pose a danger to human
health and the environment if handled or disposed of in-
correctly. However, these components are necessary
for the proper operation of the device. Devices marked
with this symbol must not be disposed of with regular
household rubbish.
Notes about the ingredients (REACH)
You will find current information about the ingredients at:
www.kaercher.com/REACH
Proper use
WARNING
The appliance is not suitable for vacuuming dust which
endangers health.
– The machine is meant for dry and wet cleaning of
floors and walls.
– This appliance is suited for the commercial use,
e.g. at construction sites, in industrial systems, in
workshops and rental companies.
1
2
3
4
5
6
7
8
9
10 Floor nozzle (Adv only)
11 Floor nozzle (not Adv)
12 Suction tube
13 Main switch
14 Suction head
15 Carrying handle
EN 1
16 Cable hook
EN 1
17 Bender
EN 1
18 Cartridge filter
EN 1
19 Fastening nut
EN 2
20 Float
EN 2
EN 2
EN 2
EN 2
ATTENTION
EN 2
Risk of damage! For dry vacuuming, the cartridge filter
EN 2
must always be installed.
EN 3
–
EN 3
EN 4
Inserting the paper filter bag
Illustration
Illustration
 Release and remove the suction head.
 Insert the paper filter bag.
 Insert and lock the suction head.
Inserting the rubber lips
Illustration
 Remove the brush strips.
 Install the rubber lips.
Note: The structured side of the rubber lips must point
outwards.
Remove the paper filter bag
–
Installing an additional filter
 Release and remove the suction head.
 Turn the suction basket by 180° and keep it aside.
 Loosen the mounting nuts
 Remove the cartridge filter.
Illustration
 Insert the fastening nut and tighten it.
 Install the additional filter.
 Insert and lock the suction head.
Illustration
The suction hose is equipped with a clip system. All C-
35/C-DN-35 accessories can be connected.
– 1
EN
Device elements
Nameplate
Power cord
Holder for suction pipes
Holder for crevice nozzle
Suction hose
Suction head lock
Steering roller
Dirt receptacle
Suction support
Start up
Dry vacuum cleaning
To vacuum fine dust, you can also use an addition-
al paper filter bag.
Wet vacuum cleaning
To suck wet dirt, first remove the paper filter bag.
Clip connection
9