OcCre 53007 SAN FRANCISCO Bastelanleitung Seite 3

PHOTO 23. Using a knife or a saw trim off any excess from the strips as you fit them into place.
PHOTO 24. Glue the short strips 49 into place in the same way as you did with the long ones.
PHOTO 25. First sand down the whole surface of the roof and then apply filler to cover up any imperfections. Sand and fill again
and keep on repeating until you have a smooth and homogeneous surface. Paint the exterior surface of the clerestory brown
and the roof grey.
PHOTO 26. Cut out and remove the centre span of the arches that hold up the roof, leaving the gap for the clerestory free.
PHOTO 27. Make up the bars 50, using the template and paint them white. Glue them into place in the holes in the floor and
glue them to the ceiling using fast-acting glue.
PHOTO 28. Fit and glue the arches of the clerestory 51. Use white glue and varnish. Varnish the underside of the clerestory roof
strips 52. Paint the lamps 53. Start to line the clerestory with the strips, working from the centre out, allowing each length of strip
to extend 5 mm at both ends. Using fast-acting glue, glue the lamps to the interior, and then continue lining the clerestory roof.
PHOTO 29. Round off the corners of the clerestory roof. Sand down and fill until the surface is smooth and homogeneous, as
you did with the main roof. Paint the roof grey and the edges brown.
PHOTO 30. Fit and glue the front pieces 54 and the corner pieces 55 into place. Between the corner pieces fit the side finishing
strips 56. Fill and file the joints between corner pieces and side finishing pieces until you leave a smooth surface. Paint the
whole profile burgundy red.
PHOTO 31. Glue the bell-pulls 57 to the lengths of brass wire 58. Paint the bell-pulls brown. Glue the other end of the strip to
the roof of the clerestory, in the centre of the arch preceding the lamp in the exterior cabins.
PHOTO 32. Glue the turning platforms 60 & 61 into place, centred on the hole in the base of the rolling gear 59. Use white glue.
PHOTO 33. Fit and glue the bushings 62. Make sure that they are perpendicular to the base. Use fast-acting glue. Paint metal
colour.
PHOTO 34. Glue the reinforcements 64 under the base 63 and glue the supports 65 onto the sides. Insert, without gluing, the
rings 67 onto the axle 66 and then fit it into the holes in the supports. Glue the wheels 68 to the ends of the axle. Slide the rings
up to the supports and glue them to the axle, making sure that the wheels can turn freely. The distance between the exterior
part of the lips on the wheels must be 45 mm.
PHOTO 35. Attach the wheel assembly to the rolling gear using the screws 69. Do not glue them in case, at some future date,
you may decide to motorise the model. Paint metal colour.
PHOTO 36. Pin and glue the supports 71 to the cow-catcher 70 using the pins 72. Cut off the ends of the pins that protrude to
the other side. Glue this assembly to the rolling gear. Paint grey and metal colour.
PHOTO 37. Cut the brass wire parts 73 to length and insert and glue them in place ion the holes in the base.
PHOTO 38. Using the screws 74 and the washers 75 attach the rolling gear to the base. Do not make the screws up too tightly.
PHOTO 39. The rolling gear must be able to turn freely, between the stops, to right and left.
PHOTO 40. Using fast-acting glue, fit and glue the track cleaners 76.
PHOTO 41. Fit and glue the side protectors 77 to two pieces of netting 78 cut and laid out as shown in the image. Use fast-
acting glue. Using a cutter trim off the excess leaving the tabs free to slot into place. Paint it black. Fit and glue the protectors to
the base.
PHOTO 42. Paint the bumpers 79 black. Fit the bumpers and, using fast-acting glue, glue them to both ends of the cable car.
PHOTO 43. Cut to length the strips 80 & 81 and make 1.5 mm diameter holes in them where indicated in the image. Varnish the
strips.
PHOTO 44. Using fast-acting glue fit and glue the supports 82 to the strips. Glue these into place using white glue. Make sure
the strips are correctly aligned, as indicated. Paint the base of the central strips blue, as shown.
PHOTO 45. Glue the supports 84 onto the backs of the steps 83, aligning the existing holes in the parts, into which we have to
insert the pins 72 and glue with fast-acting glue. Cut off the excess of the pins that protrude at the back. Glue the step 85 into
place. Make up two assemblies for each side of the cable car. Paint the assemblies as indicated and then check out the next
step.
PHOTO 46. Fit and glue the steps onto the base of the cable car, making sure that the holes are aligned with the supports. Use
white glue. At the bottom, using quick-acting glue, glue the step reinforcements 86 into place.
PHOTO 47. Cut to size the bars 87 using brass wire according to the template on the decorations sheet. Also cut to size the
bars 88 & 89. Pass the bars through the supports and insert them into the holes left in the steps for this purpose, for the bars 87,
and in the bumper for the bars 89. Use fast-acting glue. Paint black and white as shown in the image.