Makita DFL300F Betriebsanleitung Seite 6

NOTE:
• If the indicator lamp does not turn on or flicker when
charging, the battery may be faulty. In this case, ask
your local service center.
When using
When the tool is switched on, the lamps will light to
indicate the remaining battery capacity. When the tool is
switched off, the light goes out after approx. 5 seconds.
When pushing the check button with the tool switched
off, the indicator lamps turn on for approx. 5 seconds to
show battery capacity.
If the orange lamp flickers, the tool stops because of little
remaining battery capacity (Auto-stop mechanism).
Charge the battery cartridge or use a charged battery
cartridge at this time.
When the tool is used with the battery that has not been
used for a long time and is switched on, no lamps may
light up. The tool stops because of little remaining battery
capacity at this time. Charge the battery properly.
Switch action (Fig. 3)
CAUTION:
• Before inserting the battery cartridge into the tool,
always check to see that the switch trigger actuates
properly and returns to the "OFF" position when
released.
To start the tool, simply pull the switch trigger. Release
the switch trigger to stop.
LED indicator / Beeper
LED indicator / Beeper on the tool shows the following functions.
Function
This function works when the tool has
reached the preset fastening torque
Auto-stop
and normal tightening has been
fastening
completed. This helps overtightening to
be avoided.
For approximately one second after
Delayed re-start auto-stop fastening, the tool does not
start even if the switch trigger is pulled.
Insufficient fastening has been
Warning against
performed when the switch trigger has
insufficient
released before reaching the preset
fastening
fastening torque.
Warning for This indicates the appropriate time to
battery cartridge replace the battery cartridge when the
capacity battery power becomes low.
Checking the
This function works when the battery
remaining battery
power is almost used up. At this time,
capacity,
tool stops immediately.
Auto-stop
This function works to check the proper
Check the LED
operation of the LED indicator, light
indicator, light and
and beeper when a battery cartridge
beeper operation
has been inserted into the tool.
This function works when an abnormal
Anti-reset of
drop of the battery voltage occurs for
controller
some reason and the tool stops.
6
Reversing switch action (Fig. 4)
• Always check the direction of rotation before operation.
• Use the reversing switch only after the tool comes to a
• When not operating the tool, always set the reversing
This tool has a reversing switch to change the direction
of rotation. Depress the reversing switch lever from the
A side for clockwise rotation or from the B side for
counterclockwise rotation.
When the reversing switch lever is in the neutral position,
the switch trigger cannot be pulled.
Lighting up the lamps (Fig. 5)
• Do not look in the light or see the source of light
Pull the switch trigger to light up the lamp. The lamp
keeps on lighting while the switch trigger is being pulled.
The light automatically goes out 10 seconds after the
switch trigger is released.
NOTE:
• Use a dry cloth to wipe the dirt off the lens of lamp. Be
Status
CAUTION:
complete stop. Changing the direction of rotation
before the tool stops may damage the tool.
switch lever to the neutral position.
CAUTION:
directly.
careful not to scratch the lens of lamp, or it may lower
the illumination.
Status of
the LED indicator/beeper
LED indicator Beeper
Lights up in
green for
—
approximately
one second.
Lights up in
A long beep
red.
Flickers in red A series of
slowly. long beeps
Lights up in
A long beep
red.
Lights up first
in green, next A series of
red. (And then very short
the light beeps
comes on.)
Flickers in red
A series of
and green
short beeps
alternatively.
Action to be taken
—
Retighten the screw.
Replace the battery
with fully charged
one.
Replace the battery
with fully charged
one.
—
Replace the battery
with fully charged
one.