Maintenance; Ec Declaration Of Conformity; Mains Connection - Milwaukee MS 304 DB Originalbetriebsanleitung

Refrain from removing any cut-offs or other parts of the workpiece
from the cutting area whilst the machine is running and the saw
head is not in the rest position.
Never reach into the danger area of the machine when it is running.
Any faults with the machine, including any related to the safeguard
or the saw blades, must be reported to the persons in charge of safety
as soon as the faults are discovered.
Do not use any flanges other than those supplied or indicated in the
instruction manual to secure the saw blade.
Replace the table insert when worn.
Do not use saw blades which are damaged or deformed.
Do not use saw blades not corresponding to the key data given in
these instructions for use.
Do not use saw blades made of high-speed steel.
Only use saw blades which have been properly sharpened. It is essen-
tial to adhere to the maximum speed specified on the saw blade.
Transport and store the tools in a suitable receptacle.
It is necessary to select a saw blade which is suitable for the material
being cut.
Never use the mitre saw to cut materials other than those specified in
the instruction manual.
Long workpieces must be adequately supported.
Stock having a round or irregular cross section (such as firewood)
must not be cut, as it can not be securely held during cutting. When
sawing thin stock layed on edge, a suitable auxilary fence must be
used for firm support.
SPECIFIED CONDITIONS OF USE
The mitre saw can be used for sawing solid wood, bonded wood,
glued veneer, materials similar to wood, aluminium profiles, Non-
ferrous metals and plastics.
Do not use this product in any other way as stated for normal use.
EC-DECLARATION OF CONFORMITY
We declare under our sole responsibility that the product described
under "Technical Data" fulfills all the relevant provisions of the
directives 2011/65/EU (RoHs), 2004/108/EC, 2006/42/EC and the
following harmonized standards have been used:
EN 61029-1:2009 + A11:2010
EN 61029-2-9:2009
EN 55014-1:2006+A1:2009+A2:2011
EN 55014-2:1997 + A1:2001 + A2:2008
EN 61000-3-2:2006+A1:2009+A2:2009
EN 61000-3-3:2008
Winnenden, 2014-02-25
Alexander Krug / Managing Director
Authorized to compile the technical file
Techtronic Industries GmbH
Max-Eyth-Straße 10, 71364 Winnenden, Germany

MAINS CONNECTION

Connect only to single-phase AC current and only to the system
voltage indicated on the rating plate. It is also possible to connect
to sockets without an earthing contact as the design conforms to
safety class II.
Deutsch
All manuals and user guides at all-guides.com

MAINTENANCE

Be sure to disconnect the tool from the power supply before atta-
ching or removing the saw blade.
Clean the tool and guarding system with clean cloths.
The ventilation slots of the machine must be kept clear at all times.
Use only Milwaukee accessories and Milwaukee spare parts. Should
components need to be replaced which have not been described,
please contact one of our Milwaukee service agents (see our list of
guarantee/service addresses).
If needed, an exploded view of the tool can be ordered. Please state
the machine type printed as well as the six-digit No. on the label
and order the drawing at your local service agents or directly at:
Techtronic Industries GmbH, Max-Eyth-Straße 10, 71364 Winnenden,
Germany.
SYMBOLS
CAUTION! WARNING! DANGER!
Always disconnect the plug from the socket before carrying
out any work on the machine.
Please read the instructions carefully before starting the
machine.
Wear ear protectors!
Always wear goggles when using the machine.
Wear gloves!
Always keep hands away from the path of the saw blade.
Never expose tool to rain.
Do not dispose of electric tools together with household
waste material! In observance of European Directive
2002/96/EC on waste electrical and electronic equipment
and its implementation in accordance with national law,
electric tools that have reached the end of their life must
be collected separately and returned to an environmentally
compatible recycling facility.
Class II tool Tool in which protection against electric
shock does not rely on basic insulation only, but in which
additional safety precautions, such as double insulation or
reinforced insulation, are provided.
There being no provision for protective earthing or reliance
upon installation conditions.
European Conformity Mark
GB
GB
English English
23