Rs-232, Serial Control Input; Power Plug - WolfVision EYE-12 Bedienungsanleitung

External Infrared (IR) Sensor
In some rooms, the built-in IR-receiver may
infrared receiver to the IR-SENSOR plug (#12) and position the IR-sensor somewhere on the ceiling (or in
the room) where the users normally point the remote control at.
DVI-I Port
The DVI-I port (#13) provides digital and analog signals.
For using HDMI, a DVI-HDMI cable or adapter is required.
Pin 8
Pin 1
Pin 9
Pin 17
Pin 24
DVI-I connector female
(front side, unit)
RGB Port
The RGB port (#11) provides analog RGBHV signal.
5 1
15
11
15-pin D-Sub HD
connector female
(front side, unit)

RS-232, Serial Control Input

The serial port (#10) can be used to control the EYE-12 through an external device, such as a room control
system.
1 2 3 4 5
6 7 8 9
9-pin D-Sub connector
on unit; male
(front side)
The complete protocol can be found on our internet website under: www.wolfvision.com (Support)

Power Plug

When a locked power connector and/or other power supply is necessary, the
supplied power connector can be used.
The power supply is optional if Power over Ethernet (PoE) is used (see page 12).
+ 12V
The power source equipment shall comply with all applicable local and
GND
national codes related to safety.
(optional)
1 - T.M.D.S. Data2-
2 - T.M.D.S. Data2+
C1
C2
3 - T.M.D.S. Data2/4 Shield
4 - T.M.D.S. Data4- (*)
5 - T.M.D.S. Data4+(*)
C3 C4
6 - DDC Clock
C5
7 - DDC Data
8 - Analog Vertical Sync
C1 - Analog Red
C4 - Analog Horizontal Sync
C5 - Analog Ground
(analog R, G & B return)
1 - Analog Red video
2 - Analog Green video
3 - Analog Blue video
4 - N/C Not connected
5 - GND Ground
Pins: 2: RX, 3: TX, 5: GND
Baud Rate: 9200, 19200, 38400, 57600 or 115200 (selectable)
databits: 8, stopbit: 1, parity: no
The baud rate can be changed in the on-screen extra menu by keeping
pressed the menu key until it appears (see page 10).
not be enough . In this case connect the optional external
9 - T.M.D.S. Data1-
10 - T.M.D.S. Data1+
11 - T.M.D.S. Data1/3 Shield
12 - T.M.D.S. Data3- (*)
13 - T.M.D.S. Data3+ (*)
14 - +5V Power
15 - Ground (return for +5V,
HSync and Vsync)
16 - Hot Plug Detect
C2 - Analog Green
6 - Red return
7 - Green return
8 - Blue return
9 - SENSE +5 V DC from Visualizer
10 - GND Ground (VSync, DDC)
11
17 - T.M.D.S. Data0-
18 - T.M.D.S. Data0+
18 - T.M.D.S. Data0+
19 - T.M.D.S. Data0/5 Shield
20 - T.M.D.S. Data5- (*)
21 - T.M.D.S. Data5+ (*)
22 - T.M.D.S. Clock+
23 - T.M.D.S. Clock-
24 - Analog Vertical Sync
C3 - Analog Blue m
*...not used
11 - N/C Not connected
12 - SDA I²C data
13 - HSync Horizontal sync
14 - VSync Vertical sync
15 - SCL I²C clock