Routine And Special Maintenance; Pre-Installation Requirements; Technical Information - glass 1989 REEF Installations-, Bedienungs- & Wartungsanleitung

EN
Serial number (Figure A) to state in each intervention request.
Do not remove the sticker from the product!
Figure A
WARNING.
• Read the manual carefully in all its parts before using the
product.
• Keep this manual for further consultation.
• The manual is intended for different models and versions, so
the product may look different from the manual illustrations.
However the instructions remain unchanged.
• The company reserves the right to make any changes
considered suitable without notice or replacement.
• This product is intended only for the use for which it has been
designed. The manufacturer is not responsible for any damage
caused by improper usage.
• The product identification data (model, power, voltage,
manufacturer's name) are contained in the silver data plate on the
unit and on the warranty card. It is issued at the time of testing.
• Make sure that the drain is always efficient.
• Install a water softener to eliminate scale.
• Ensure that the floor around the product is always dry and clean,
to avoid slips or falls entering or editing the product itself.
• Pay maximum attention when the surrounding floor is wet,
as there will be a potentially high risk of slipping. this, mainly,
when using soaps, shampoos, clearing detergents, etc..
• It is not advisable to use the shower cabin with water that is too
hot. Use water with a maximum temperature of 38°C.
• People affected by obesity, weak heart condition or blood
pressure disorders, circulation problems, diabetes, elderly
people or pregnant women should consult a doctor before
using the product.
• People who take medicines should consult a doctor before
using the product as some medicines may cause sleepiness,
affect heart beat, blood pressure and circulation.
• Do not use alcoholic substances, drugs or medicines before
and during the use of the product as they could cause
unconsciousness.
• This product is not intended to be used by persons (including
children) with reduced physical, sensory or mental capabilities
or lack of experience or knowledge, unless they have been
given appropriate supervision or instruction concerning use
of the appliance by a person responsible for their safety.
• WARNING: children may use the product unsupervised only
when its operation has been clearly explained to them and
they are able to use it safely while recognising the dangers
of misuse.
• When the product is not used, disconnect it completely by
turning off the double-pole switch installed on upstream the
appliance.
All measurements are in mm.

PRE-INSTALLATION REQUIREMENTS

The requested floor load is of Min. 200 Kg/m². The premises
fitting the product must, therefore, meet this condition.
To prevent damaging the mixer parts, place a filter upstream of
the mixer.

TECHNICAL INFORMATION:

• Minimum flow pressure:
• Operating pressure:
• Recommended operating pressure:
• Hot water temperature:
The power supply box, to be connected to point C.V. (see Pre-
installation requirements) is supplied in all versions except the
manual version.
To make the electrical connection to the power supply box (only
for product versions supplied with the power supply box) use an
H07 RN-F cable with diameter of 2.5 mm².
When making the connection to the electrical mains, a double-
pole switch must also be fitted near the appliance, upstream of
the power supply box, with contacts opening by at least 3 mm,
and suitable for 220/240 V 16 A.
The appliance must be connected to an electrical system
provided with a 0.03 A differential thermal breaker.
The product's supporting structure is metallic. An efficient
ground system is therefore required, with sensitivity meeting
the relevant standards.
GROUNDWIRE.
The ground wire must be connected and fixed permanently
to the electrical system.
EQUIPOTENTIAL CONNECTION.
The equipment must be connected to the equipotential
system of the room and duly fastened to its terminal to be
found in the product.
The following accessories
manufacturer) are required for installation:
a) Fittings to connect the mixer to the domestic water mains
(connection to mixer via ½" fittings) pipes provided in the
kit and no other types of piping must be used.
b) fittings needed to connect the sunken drainage to the drain
column of the bath (connection to waste column with 1 ½"
collar waste trap)
ROUTINE AND
SPECIAL MAINTENANCE
To clean, see the "Cleaning and Maintenance" guide
accompanying the product.
Special maintenance must be carried out by qualified
personnel.
In case of failures or malfunctioning of the product, contact
only authorised technicians to avoid losing warranty rights. The
manufacturer shall not be held responsible for any damage
caused by products that have been tampered with or repaired
wrongly.
Limescale can be removed from water jet
nozzles simply by rubbing.
10
150 kPa (1,5 bar)
350 kPa (max 3,5 bar)
250 kPa (2,5 bar)
max 60°C
(not supplied by the