Inhaltsverzeichnis
Werbung
OBJ_BUCH-1676-002.book Page 10 Tuesday, October 22, 2013 11:57 AM
10 | English
Hold bar against branch firmly, do not apply large force - al-
low the pruner to cut through at its natural rate. (see fig. 6)
AMW 10 power unit is fitted with an over-current protection
device. Excessive pressure applied to the pruner chain and
bar in use can cause the protection device to operate.
Reduce force before the branch is completely cut off. You can
get injured, when losing balance and control of the pruner.
Work in steps on thick branches: (1) cut ¼ from below; (2)
cut off from top further outside; (3) cut off the stump at the
stem. (see fig. 6)
Symbols
The following symbols are important for reading and under-
standing the operating instructions. Please take note of the sym-
bols and their meaning. The correct interpretation of the sym-
bols will help you to use the garden product in a better and safer
manner.
Symbol
Meaning
Wear protective gloves
Wear eye protection.
Wear hard hat.
Wear substantial footwear.
Always wear ear protection.
Reaction direction
Movement direction
Intended Use
This multi-tool attachment can only be operated by the power
unit AMW 10.
The pole pruner is intended for cutting trees and shrubs in pri-
vate use. The pole pruner may not be used for felling trees.
Maintenance and Cleaning
Warning! Switch off, remove plug from mains before ad-
justing or cleaning.
Note: To ensure long and reliable service, carry out the following
maintenance regularly.
For safe and proper working, always keep the garden product
and the ventilation slots clean.
F 016 L70 917 | (22.10.13)
Regulary check the pole pruner or obvious defects such as loose,
dislodged or damaged saw chain and chain bar, loose fixings and
worn or damaged components.
Check that covers and guards are undamaged and correctly fit-
ted. Carry out necessary maintenance or repairs before using.
If the pole pruner should fail despite the care taken in manufac-
ture and testing, repair should be carried out by an authorised
customer services agent for Bosch power tools.
Note: Before returning the pole pruner, ensure all oil in the oil
reservoir has been emptied.
In all correspondence and spare parts orders, please always in-
clude the 10-digit article number given on the type plate of the
garden product.
Replacing/Changing the Saw Chain and Chain Bar
Check the saw chain and chain bar according to section
"Kettenspannung einstellen".
The circular groove of the chain bar will wear particularly on the
lower edge with time. When replacing the saw chain, turn the
chain bar by 180° to allow even wear, thus extending chain bar
life.
Check the drive sprocket . If it is worn out or damaged due to
strain, have it exchanged by an authorized Bosch after-sales ser-
vice.
Sharpening the Saw Chain
Have your chain sharpened professionally at your authorized
Bosch after-sales service or sharpen the chain yourself using the
Bosch sharpening kit or the Dremel Multi power tool with the ap-
propriate grinder (1453). Observe the sharpening instructions
provided with the sharpening kit.
Checking the Automatic Oiler
Proper functioning of the automatic saw chain oiler can be
checked by running the pole pruner and pointing the tip of the
chain bar towards a piece of cardboard or paper on the ground.
Do not touch the ground with the chain and ensure a safety clear-
ance of 20 cm. If an increasing oil pattern developes, the auto-
matic oiler is operating fine. If there is no oil pattern despite a full
oil reservoir, see section "Troubleshooting" or contact your au-
thorized Bosch after-sales service.
After Use/Storage
Clean the moulded plastic housing of the pole pruner using a soft
brush and clean cloth. Do not use water, solvents or polishes.
Remove all debris, especially from the motor cooling vents.
After 1 – 3 hours of use, remove the cover , the chain bar and
the saw chain , and clean them using a brush.
Clean the area under the cover, the drive sprocket and the chain
bar assembly from adherant debris using a brush. Clean the oil
outlet with a clean cloth.
If the pole pruner is to be stored for a longer period of time, clean
the saw chain and the chain bar.
Store the pole pruner in a secure, dry place, out of the reach of
children.
Do not place other objects on the garden tool.
Bosch Power Tools
Werbung
Inhaltsverzeichnis
