OCEAN U4 Allgemeine Hinweise Gratulation zum Kauf Ihres elektronischen Wichtige Installationshinweise: Urinal-Druckspülers WimTec OCEAN U4. Die Montage und Installation darf nur durch Damit Sie lange Jahre Freude mit dieser hoch- einen konzessionierten Fachbetrieb, gemäß wertigen Armatur haben, empfehlen wir Ihnen DIN 1988, ÖVE/ÖNORM E 8001 sowie VDE...
R 1/2“ IG Putz 230 V Ablauf 25,5 R 1/2“ AG min. 98 max. 158 Montage: Maße in cm 230 V (bei Netzausführung) Bei 230 V Netzbetrieb Elektro-Leerverrohrung vorsehen. Spannungsversorgung: OK-FFB 2 x 0,75 mm - 1,5 mm WimTec OCEAN U4 Urinaldruckspüler...
All manuals and user guides at all-guides.com OCEAN U4 Legende WimTec OCEAN U4 Frontplatte: Vorderseite: Rückseite: AquaCap-Taster zum Aktivieren einer Spülung Spülzeit-Regler für die Dauer der Hauptspülung (5 s voreingestellt, 1 s bis 10 s einstellbar) Anschluss Magnetventil Anschluss Netzteil oder...
Vorabsperrung wieder schließen. Schmutzsieb-Abdeckung öffnen. Schmutzsieb und Schmutzsieb-Abdeckung wieder einsetzen. Magnetventiladapter mit Dichtungen einsetzen (Flussrichtung beachten!). Kabel für Spannungsversorgung in das Rohbauset einziehen (nur bei 230 V Netzversion). Versorgungskabel mit Netzteil verbinden (nur bei 230 V Netzversion). WimTec OCEAN U4 Urinaldruckspüler...
Seite 9
Folgende Schritte unbe- dingt in beschriebener Reihenfolge ausführen! Netzteil bzw. Batteriemodul in Rohbauset einschieben. Montagerahmen ausrichten und festschrauben. Magnetventil mit Elektronikmodul verbinden. Netzteil bzw. Batteriemodul mit Elektronikmodul verbinden und bei Netzversion Spannungszufuhr aktivieren (Sicher- heitsschließimpuls beim Magnetventil erfolgt). WimTec OCEAN U4 Urinaldruckspüler...
Seite 10
All manuals and user guides at all-guides.com OCEAN U4 Montage ACHTUNG! Folgende Schritte unbe- dingt in beschriebener Reihenfolge ausführen! Vorabsperrung öffnen. Falls erforderlich Einstellungen am Elektronikmodul anpassen (siehe Seite 6). Frontplatte aufsetzen - Funktionsprüfung durchführen. Mit Schraube von unten sichern. WimTec OCEAN U4 Urinaldruckspüler...
OCEAN U4 General notes Congratulations on purchasing WimTec Important installation notes: OCEAN U4, your electronic urinal flush valve. Mounting and installation may only be Please take note of the following cleaning performed by a qualified service provider in and maintenance recommendations in order accordance with DIN 1988, ÖVE/ÖNORM...
Seite 13
All manuals and user guides at all-guides.com OCEAN U4 Table of contents Page Technical data ..................14 Dimensions ..................15 Legend ....................16 Function ....................17 Assembly .................... 18 Spare parts ..................21 WimTec OCEAN U4 Urinal flush valve...
98 max. 158 Assembly: Dimensions in cm 230 V (mains version) When used in 230-V mains operation, provide empty duct for electrical installation. Power supply: 2 x 0.75 mm - 1.5 mm OK-FFB WimTec OCEAN U4 Urinal flush valve...
All manuals and user guides at all-guides.com OCEAN U4 Legend WimTec OCEAN U4 front plate: Front side: Rear side: AquaCap button for activating a flush Flush time control for the duration of the main flush (5 s preset, adjustable from...
Insert magnetic valve adapter with gaskets (observe direction of flow!). Feed cable for the power supply into the flush-mount set (only for 230-V mains version). Connect power cable with power supply (only for 230-V mains version). WimTec OCEAN U4 Urinal flush valve...
Seite 19
Connect magnetic valve with electronics module. Connect power supply or battery module with the electronics module and in the case of the mains version, activate the voltage supply (causing the safety locking mechanism of the magnetic valve to activate). WimTec OCEAN U4 Urinal flush valve...
Seite 20
Open the integrated stop valve. If required, adjust the electronics module with the desired settings (see p. 16). Position the front plate - perform function check. Secure from below with a screw. WimTec OCEAN U4 Urinal flush valve...