Seite 1
All manuals and user guides at all-guides.com Bedienungsanleitung Operating instructions Notice pour utilisateurs Kapazitiver Niveauschalter Capacitive level switch Détecteur de niveau capacitif...
All manuals and user guides at all-guides.com Montage Montieren Sie den Niveauschalter wie abgebildet: Nicht medienberührend Medienberührend (nur für nichtmetallische Behälter) Elektrischer Anschluss Schalten Sie die Anlage span- nungsfrei. Schließen Sie das Gerät an (siehe Typenschild). Bedienung Gleichen Sie den Sensor ab. Drücken Sie dazu die Program- miertaste mit einem stumpfen Gegenstand.
Seite 4
All manuals and user guides at all-guides.com Leerabgleich Das Gerät muß nach dem Einbau in den leeren Behälter abgeglichen werden (Leerabgleich). Als „leer“ kann der Behälter dann betrachtet werden, wenn das zu erfassende Füllgut mindestens 20 mm von der aktiven Zone entfernt ist. Erfasst der Sensor nach dem Abgleich ein Füllgut, ändert sich sein Schaltzustand.
Seite 5
All manuals and user guides at all-guides.com Vollabgleich Nach dem Leerabgleich soll, wenn möglich, der Vollzustand hergestellt werden, so dass das Gerät schaltet. Drücken Sie die Programmiertaste, bis die grüne LED schnell blinkt 5 ... 10 (= Gerät ist im Abgleichmodus). Die LED blinkt zunächst langsam (ca.
Seite 6
All manuals and user guides at all-guides.com Wird dieser Vorgang aus dem verriegelten Zustand heraus gestartet, so zeigt die grüne LED 10 s lang keine Reaktion. Nach 10 s ist das Gerät entriegelt (siehe "Entriegeln"). Entriegeln min. 10 s Drücken Sie die Programmiertaste mind. 10 Nach ca.
All manuals and user guides at all-guides.com Weitere Fehlerarten: • Elektronischer Fehler oder Beschädigung des Gerätes im Sensorbe- reich • Interner Fehler (kann nur durch Aus- und wieder Einschalten der Betriebsspannung gelöscht werden, Hardware-Reset) Inbetriebnahme/Betrieb Prüfen Sie, ob das Gerät sicher funktioniert. Bringen Sie dazu den Sen- sor durch geeignete Maßnahmen zum Ansprechen.
All manuals and user guides at all-guides.com Contents Page Function and features ------------------------------------------------------ 8 Mounting -------------------------------------------------------------------- 9 Electrical connection -------------------------------------------------------- 9 Operation -------------------------------------------------------------------- 9 Programming -------------------------------------------------------------------- 9 Set-up/Operation ---------------------------------------------------------- 13 sensing face LEDs red, yellow, green threaded sleeve programming pushbutton Function and features •...
All manuals and user guides at all-guides.com Mounting Mount the level switch as shown: Not in contact with the medium In contact with the medium (only for non-metallic tanks) Electrical connection Disconnect the installation from power. Connect the unit (see type label).
Seite 10
All manuals and user guides at all-guides.com Empty adjustment The unit must be adjusted after installation in the empty tank (empty adjustment). The tank can be considered to be "empty" when the medium to be detected is min. 20 mm away from the active zone. If the sensor detects a medium after adjustment, its switching status changes.
Seite 11
All manuals and user guides at all-guides.com Full adjustment After empty adjustment the full state is to be achieved, if possible, so that the unit switches. Press the programming pushbutton until the green LED flashes quickly 5 ... 10 s (= the unit is in the adjustment mode).
Seite 12
All manuals and user guides at all-guides.com Unlocking min. 10 s Press the programming pushbutton for min. 10s. After approx. 10 s the green LED flashes briefly for 2x. The unit is unlocked again and the LEDs indicate the current operating state. When the programming pushbutton is released the unit is unlocked and all programming functions are active again.
All manuals and user guides at all-guides.com Further faults: • Electronic fault or sensing zone of the unit damaged • Internal fault (can only be deleted by power off and then power on again, hardware reset). Set-up / Operation Check the safe functioning of the unit. To do so, bring about a sensor response by taking suitable measures.
All manuals and user guides at all-guides.com Contenu Page Fonctionnement et caractéristiques ------------------------------------ 14 Montage -------------------------------------------------------------------- 15 Raccordement électrique-------------------------------------------------- 15 Manipulation ---------------------------------------------------------------- 15 Programmation ---------------------------------------------------------------- 15 Mise en service / Fonctionnement -------------------------------------- 19 face active LED rouge, jaune, verte tube fileté bouton-poussoir de programmation Fonctionnement et caractéristiques •...
All manuals and user guides at all-guides.com Montage Monter le détecteur de niveau selon l'illustration: Sans contact avec le fluide En contact avec le fluide (seulement pour des cuves non métalliques) Raccordement électrique Mettre l'installation hors tension. Raccorder le détecteur (voir l'étiquette).
Seite 16
All manuals and user guides at all-guides.com Réglage vide Après le montage dans la cuve vide, l'appareil doit être réglé (réglage vide). La cuve peut être considérée comme "vide" si le fluide à détec- ter est au min. à 20 mm de la zone active. Si le détecteur détecte un fluide après le réglage, il change son état de commutation.
Seite 17
All manuals and user guides at all-guides.com Réglage plein Après le réglage vide, le réglage plein doit être réalisé, si possible, de façon à ce que l'appareil commute. Appuyer sur le bouton-poussoir de programma- tion jusqu'à ce que la LED verte clignote rapide- 5 ...
Seite 18
All manuals and user guides at all-guides.com Si cette opération est effectuée en état verrouillé, la LED verte s'éteint brièvement, et ensuite ne réagit plus. Déverrouiller min. 10 s Appuyer sur le bouton-poussoir de pro- grammation pendant min.10 s. Après environ 10 s la LED verte clignote 2 fois brièvement.
All manuals and user guides at all-guides.com Aide: Eviter l'erreur mentionnée et répéter le réglage pour corriger l'erreur. D'autres erreurs: • Défaut électronique ou endommagement de l'appareil dans la zone de détection • Défaut interne (peut seulement être effacé par la mise hors tension et de nouveau sous tension, reset hardware) Mise en service / Fonctionnement Vérifier le bon fonctionnement de l'appareil.