KIKKA BOO BABY WALKER ABC Gebrauchsanweisung Seite 9

THANK YOU FOR CHOOSING OUR PRODUCT.
IMPORTANT!READ CAREFULLY BEFORE USE AND KEEP THEM FOR FUTURE REFERENCE.
COMLIES WITH EN1273:2020
WARNING!
• This product is intended only for a child who can sit up by itself and until it is able to walk by itself or weight more than 12 kg.
• Before using, remove and dispose of any plastic bags and any other packaging(e. g fasteners, fixing ties, etc. ) and keep them out of reach of children.
• Before using, check that the product and all of its components have not been damaged during transportation. Check regularly that the product is not broken or damaged.
If the product is broken or damaged, keep out of reach of children.
• The product must only be assembled by an adult. For the correct assembly of the product, please refer to the following instructions.
• STAIR HAZARD: Avoid serious injury or death. Block stairs/ step securely before using walker even when using parking brake.
• The child will be able to reach further and move rapidly when in the walking frame.
Prevent access to stairs, steps and uneven surfaces, slopes or unstable floors, swimming pools or other sources of water. Only use the baby walker frame on flat and stable
surfaces.
Never leave child unattended. Always keep child in view while in walker.
• Guard all fires, heating and cooking appliances.
• Remove hot liquids, electrical cables and other potential hazards from reach.
• Prevent collisions with glass in doors, windows and furniture.
• Do not use the baby walking frame if any components are broken or missing.
• This baby walking frame should be used only for short periods of time(e.g.20 min).
• Do not use accessories or replacement parts other than those approved by the manufacturer or distributor.
PARTS
Check that you have all the parts for this model BEFORE assembling your product. No tools required.
A. 2 wheels; B. 2 rear fix wheels; C. 6 safe rubbers; D. Large spoiler; E. Baby walker frame; F. Padded seat; G. Electronic play tray
ASSEMBLING PROCEDURES
1A. Turn the baby walker frame upside down. Fix the wheels in the appropriate housings. Ensure that the wheels are firmly pushed all the way into the housing on the
down base of the walker.
1B. Fix the rear fix wheels in the appropriate housings. Ensure that the wheels are firmly pushed all the way into the housing on the down base of the walker.
1C. Fix the safe rubbers in the appropriate housings. Ensure that the safe rubbers are firmly pushed all the way into the housing on the down base of the walker.
2. Open the baby walker frame in the in-use position, ensuring that all wheels touch the floor. Slowly raise the tray by polling it in an upward direction, until a click
indicates that the frame has been locked correctly in one of the three positions.
3.Fit the large spoiler on the rear walker frame; simply place it on the housings, located at the rear of the backrest, and push it firmly in a downward direction, ensuring
that it has been fitted in the correct position. Please do not lift up baby walker with large spoiler. It is dangerous do in this way.
4. Insert the plastic rings of the padded seat in the slots located along the upper edge of the walker frame. Pass the rings through the slots and tug them until they clear
the passage, then release them, ensuring that they are correctly locked in the position and cannot recede into the slot.
5. Loosen the screw on the battery compartment cover with a suitable screwdriver, press the tab and remove the battery compartment cover. Fit the battery, ensuring that
they have been fitted in the correct polarity, as shown inside the battery compartment.
6. I nsert all small toy parts into corresponding holes. Put the electronic play tray into its housing in front of the walker' s seat. Listen for two click to confirm the play tray is
safely locked in place. Completely assembled.
HOW TO ADJUST THE HEIGHT OF BABY WALKER FRAME
WARNING! When opening, closing or adjusting the walker, ensure that your child is at a safe distance. Before placing the child in the walker in ensure that the secondary
lock button is correctly locked again.
7. To adjust the seat' s height, remove the child from the baby walking frame, pull up the safe button located under the small tray table and rotate it to 90 degrees. keep the
safe button pressed, then raise or lower the small table until the desired position is reached, then pull up the safe button and rotate it to 90 degrees again to lock the small
table.(If it is a automatic secondary lock, please make sure the lock rotated to 90 degrees.)
HOW TO FOLD THE WALKER
8. Press the button as picture shows, meanwhile pull down the upper tray to the end, the frame folds up completely.
FITTING AND / OR REPLACING BATTERIES
WARNING! The toy of the walker frame requires 2X"AA" 1.5Volt alkaline type batteries(not included).
• Batteries must only be fitted by an adult • To fit and/ or replace batteries: loosen the screw on the battery compartment cover with a suitable screwdriver, press the tab
and remove the battery compartment cover. Then remove the spent batteries and fit new ones, ensuring that they have been fitted in the correct polarity, as shown inside
the battery compartment. Replace the battery cover and tighten the screw • Always keep batteries and tools out of reach of children • Always remove spent batteries
from the toy to avoid the danger of possible leakage from the battery damaging the product • Always remove the batteries if the toy will not be used for a long period
• Only use alkaline batteries of the same type of equivalent to the type recommended for the correct function of this product • Never mix new and old batteries, or different
types of batteries • Do not burn or dispose of spent batteries into the environment. Dispose of spent batteries at an appropriate differentiated collection point • Do not
short-circuit the battery terminals •Do not attempt to recharge non-rechargeable batteries: they might explode • The use of rechargeable batteries is not recommended
and cannot be used.
CARE AND MAINTENANCE • Ensure that all parts are working well before use. Always check parts regularly for wheels, locking devices seat pad and so on every 15 days. • In
some climates the covers and trims may be affected by mold and mildew. To help prevent this occurring, do not fold or store the product if it is damp or wet. • Wipe plastic
parts with a damp cloth using mild soap. • To clean the seat pad, footpad, canopy, use only mild household soap and warm water with a sponge or cloth. DO NOT MACHINE
WASH.
ENGLISH