Crown CT24001HX Originalbetriebsanleitung Seite 25

Battery tool use and care
• Recharge only with the charger specified by the
manufacturer. A charger that is suitable for one type
of battery pack may create a risk of fire when used with
another battery pack�
• Use power tools only with specifically designat-
ed battery packs. Use of any other battery packs may
create a risk of injury and fire.
• When battery pack is not in use, keep it away
from other metal objects, like paper clips, coins,
keys, nails, screws or other small metal objects,
that can make a connection from one terminal to
another. Shorting the battery terminals together may
cause burns or a fire.
• Under abusive conditions, liquid may be ejected
from the battery; avoid contact. If contact acci-
dentally occurs, flush with water. If liquid contacts
eyes, additionally seek medical help. Liquid ejected
from the battery may cause irritation or burns�
• Avoid unintentional switching on. Ensure the
on / off switch is in the off position before insert-
ing battery pack. Carrying the power tool with your
finger on the on / off switch or inserting the battery
pack into power tools that have the switch in acci-
dents�
• Do not open the battery. Danger of circuit�
• In case of damage and improper use of the bat-
tery, vapors may be emitted. Provide for fresh air
and seek medical help in case of complaints. The
vapors can irritate the respiratory system�
• When the battery is defective, liquid can escape
and come into contact with adjacent components�
Check any parts concerned� Clean such parts or re-
place them, if required�
• Protect the battery against heat, e.g., also
against continuous sun irradiation and fire. There
is danger of explosion�
WARNING! Read all safety warnings and
all instructions.
• Protect the battery charger from rain and mois-
ture. The penetration of water in a battery charger in-
creases the risk of electric shock�
• Do not charge other batteries. The battery charger
is suitable only for charging lithium ion batteries within
the listed voltage range� Otherwise there is danger of
fire and explosion.
• Keep the battery charger clean. Contamination
may cause the danger of electric shock�
• Check the battery charger, cable and plug each
time before using. Do not use the battery charger
when defects are detected. Do not open the battery
charger yourself and have it repaired only by quali-
fied personnel using original spare parts. Damaged
battery chargers, cables and plugs increase the risk of
electric shock�
• Do not operate the battery charger on easily in-
flammable surfaces (e.g. , paper , textiles , etc.) or
in combustible environments. There is danger of fire
due to the heating of the battery charger during charg-
ing�
Service
• Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power tool
is maintained�
• Follow instruction for lubricating and changing ac-
cessories�
Special safety warnings
• Wait for the cutter to stop before setting the tool
down. An exposed rotating cutter may engage the
surface leading to possible loss of control and serious
injury�
NOTE: The above warning applies only to planers
without an automatic closing guard�
• Use clamps or another practical way to secure
and support the workpiece to a stable platform.
Holding the work by your hand or against the body
leaves it unstable and may lead to loss of control�
Safety guidelines during power tool op-
eration
• Accessories not recommended and specially
designed by tool manufacturer shall not be used;
damaged accessories shall not be used; specification
of the accessory shall be within rated capacity range
of the tool�
• Blade for plane shall be correctly installed and
used according to instructions provided by the
manufacturer. Attention shall be paid to the size
which must match the press plate to ensure that no
mechanical friction occurs between the blade for plane
and press plate during operation after installation� After
installation, the switch shall be started at a safe posi-
tion and the tool shall operate for 30 seconds� In case
of serious vibration or other problem, the operation
shall be stopped and arrangement shall be made for
maintenance�
• Machined workpiece shall be reliably fastened
and clamped with fixture or bench clamp to the
greatest extent.
• The fingers shall not be put on switch button to
avoid turning on the tool unconsciously when the
tool moves.
• The power tool shall be started before being
placed on material surface for processing. When
planing operation is carried out, inspection shall be
carried out to see whether any foreign matter is hid-
den in the workpiece, for example, nails and screws�
Any foreign matter discovered shall be removed before
operation�
• The power tool shall be shut off before being
put down. After cutting off the power, the power tool
could be put down only after work head of the tool is
completely static� At that time, you could not touch
the blade for plane with hands� Similarly, the blade for
place will be very hot during operation; therefore, you
shall not touch it with hands before it is cooled�
• If dust harmful to health, combustible or explo-
sive dust is generated during work, appropriate
safety measures shall be taken. For example: waste
dust that may cause cancer� During work, you should
use equipment for removal of waste dust and sweeps
and wear dust mask�
• The workplace shall be kept clean. After mixing,
the materials may be of high risk.
English
25