DECLARATION OF CONFORMITY Fabricant D-63533 Mainhausen DECLARATION DE CONFORMITE Die HAMEG Instruments GmbH bescheinigt die Konformität für das Produkt Elektromagnetische Verträglichkeit / Electromagnetic compatibility / The HAMEG Instruments GmbH herewith declares conformity of the product Compatibilité électromagnétique HAMEG Instruments GmbH déclare la conformite du produit EN 61326-1/A1 Störaussendung / Radiation / Emission:...
Transport Lagerung Sicherheitshinweise Bestimmungsgemäßer Betrieb Gewährleistung und Reparatur Wartung Umschalten der Netzspannung Sicherungswechsel Bezeichnung der Bedienelemente Einführung in den Betrieb des HM8142 Einstellung der Ausgangsspannungen und der Strombegrenzung Aufl ösung Betriebsarten Konstantspannungsbetrieb Konstantstrombetrieb Serien- und Parallelbetrieb Elektronische Last Arbitrary Funktion Triggereingang / Triggerausgang (Start/Stop) Modulationseingänge...
All manuals and user guides at all-guides.com H M 8 1 4 2 A r b i t r a r y - N e t z g e r ä t H M 8 1 4 2 2x 0-30 V/0-2 A 5 V/0-2 A NF-Arbitrarysignal Auflösung der Anzeige 10 mV/1 mA...
Ausgangsspannungen des Werden mehrere Geräte aufeinander gestellt sitzen die ein- HM8142 kann die Schutzkleinspannung von 42 V geklappten Gerätefüße in den Arretierungen des darunter lie- überschritten werden. Beachten Sie, dass in die- genden Gerätes und sind gegen unbeabsichtigtes Verrutschen sem Fall das Berühren von spannungsführenden...
Schutzklasse 2 betrieben werden. Eine D-63533 Mainhausen INTERFACE 115/230 V ±10% / 50-60 Hz Watts (max.): 160 HM8142-2 Fuse: IEC127 - III ausrei-chende Luftzirkulation (Konvektionskühlung) ist zu PROGRAMMABLE 115 V: 2 x 3,2 A / 230 V: 2 x 1,6 A...
TRIGGER IN / OUT Instruments D-63533 Mainhausen INTERFACE 115/230 V ±10% / 50-60 Hz HM8142-2 Watts (max.): 160 Fuse: IEC127 - III PROGRAMMABLE 115 V: 2 x 3,2 A / 230 V: 2 x 1,6 A POWER SUPPLY 5 x 20 mm slow blow, Made in Germany träge, temporisé, lento...
Wird bei der Einstellung die entsprechende Taste UP/DOWN zulässige Schutzkleinspannung überschritten werden kann. festgehalten, so erfolgt nach kurzer Zeit automatisches Repe- Das HM8142 darf dann nur von Personal bedient werden, das tieren in 10 mV bzw. 1 mA-Schritten. mit den damit verbundenen Gefahren vertraut ist.
3 A begrenzt. Für einen Zeitraum von ca. 200 μs kann das Netz- gerät einen Strom bis max. 3 A abgeben. Allgemeine Hinweise Kühlung In das HM8142 kann optional eine RS-232, IEEE- oder USB- Schnittstelle eingebaut werden. Wir empfehlen den Einbau Die im HM8142 erzeugte Wärme wird durch einen temperatur- ab Werk.
All manuals and user guides at all-guides.com F e r n s t e u e r u n g Beschreibung der Befehle eingestellten Grenzwerten des Stromes. Zur Abfrage der Ist- werte werden die MIx-Befehle verwendet. RM1/RMO Format: MU1 + MU2 Funktion: Einschalten des Remote-Zustandes Format: MU1 bzw.
512 Eintragungen von Spannungsund Zeitwerten zwischen „N“ und „n“ kann ein „Space“ sein. erstellt werden. Diese Wertetabelle wird in einem Speicher abgelegt und bleibt auch nach dem Ausschalten des HM8142 Funktion: Programmierung der Arbitrary-Funktion. gespeichert. Zur Bedienung und Programmierung dieser Funk- Das Netzgerät erlaubt die Anlage einer Datenliste...
Seite 13
All manuals and user guides at all-guides.com F e r n s t e u e r u n g Während der Datenübertragung zeigen die Anzeigen des Netz- gerätes folgende Werte: Anzeige links: A1 (Arbitrary-Programmierung) Auf der rechten Anzeige wird der Spannungssollwert des rechten Kanals ange- zeigt;...
Verschmutzungsgrad / Degree of pollution / Degré de pollution: 2 General information regarding the CE marking HAMEG instruments fulfi ll the regulations of the EMC directive. The 3. Infl uence on measuring instruments. conformity test made by HAMEG is based on the actual generic- and Under the presence of strong high frequency electric or magnetic fi...
Seite 15
Proper operating conditions Warranty and Repair Maintenance Mains voltage Changing the line fuse Controls and display Introduction to using the HM8142 Setting output voltages and the current limiter Resolution Operating modes Constant voltage operation (CV) Constant current operation (CC) Serial or parallel operation...
All manuals and user guides at all-guides.com H M 8 1 4 2 A r b i t r a r y P o w e r S u p p l y H M 8 1 4 2 2x 0-30 V/0-2 A 5 V/0-2 A AF arbitrary signal Display resolution 10 mV /1 mA...
If the feet are not used (picture 2) the instrument can be com- – Opening of the instrument is allowed only to qualifi ed per- bined with many other HAMEG instruments. sonnel – Prior to opening the instrument must be disconnected from In case several instruments are stacked (picture 3) the feet rest the line and all other inputs/outputs.
It is forbidden to repair defective fuses or to bridge them by any means. Any damage caused this way will void the warranty. Warranty and Repair HAMEG instruments are subject to a strict quality control. All VOLTAGE SELECTOR instruments are burned in for 10 hrs prior to shipment. By in-...
TRIGGER IN/OUT (BNC socket) (pushbutton and LED) Input/output for start and trigger signals to/from the Setting of current limit via frontpanel. When depressing the HM8142 button the setting function is active and the appertaining Voltage selector LED is lit for approx. 4 sec.
The controls are now enabled for programming. The desired output voltage or a value for current limitation can The HM8142 also offers a mode in which it functions as an elec- be input. If more than about 10 seconds elapse without any of tronic load (current sink).
Always make sure that there is suffi cient open space for coo- terminated by sending a RM0 command or pressing the LO- ling on both sides of the HM8142. In no case may the cooling CAL button. holes on the sides of the unit be covered.
Format: RU1 or RU2 Reply: U1:12.34V or U2:12.34V Format: Function: The voltage values sent back by the HM8142 are the Function: The outputs are switched on. programmed SET voltage values. Use the MUx commands to query the ACTUAL values. Format: Function: The outputs are switched off.
Seite 24
20 ms only. 50 ms 100 ms STOP When the arbitrary mode is activated, the outputs of the HM8142 200 ms are automatically activated. The arbitrary mode can be termi- 500 ms nated by 2 different means: –...
Seite 25
All manuals and user guides at all-guides.com R e m o t e c o n t r o l Subject to change without notice...
Seite 26
All manuals and user guides at all-guides.com N o t e s Subject to change without notice...
Seite 27
All manuals and user guides at all-guides.com N o t e s Subject to change without notice...