Inhaltszusammenfassung für Hameg Instruments HM 7042-4
Seite 1
Dreifach-Netzgerät HM 7042-4 VOLT AMP. VOLT AMP. VOLT AMP. FINE CURRENT ELECTRONIC VOLTAGE CURRENT OUTPUT FINE CURRENT LIMIT FUSE LIMIT ALL CHANNELS LIMIT COARSE COARSE 0 – 32 V 0 – 5.5 V 0 – 32 V POWER – –...
Bezeichnung der Bedienelemente ......... Netzgerätegrundlagen ............Lineare Netzteile ..............Getaktete Netzteile ............... Parallel- und Serienbetrieb ............. Strombegrenzung ..............Elektronische Sicherung ............Gerätekonzept des HM 7042-4 ..........Einführung in die Bedienung des HM 7042-4 ......Bedienelemente und Anzeigen ..........Änderungen vorbehalten...
Schaltungen gibt es Sicherheitseinrichtungen bringen Vorteile im täglichen Einsatz. neben einer Strombegrenzung auch eine elektronische Siche- Seit Jahren bewährt ist das HM 7042-4 auch in der Zukunft immer rung. Diese schaltet alle Ausgangsspannungen ab, sobald der ein zuverlässiger Begleiter.
– Schwere Transportbeanspruchung Überschreiten der Schutzkleinspannung! Bei Reihenschaltung aller Ausgangsspannungen des Bild 3 HM 7042-4 kann die Schutzkleinspannung von 42 V überschritten werden. Beachten Sie, dass in diesem Fall das Berühren von spannungsführenden Teilen lebensgefährlich ist. Es wird vorausgesetzt, dass nur Personen, welche entsprechend ausgebildet und un- terwiesen sind, die Netzgeräte und die daran ange-...
Wichtige Hinweise Bestimmungsgemäßer Betrieb Verwenden Sie keinen Alkohol, Lösungs- oder Die Geräte sind zum Gebrauch in sauberen, trockenen Räumen Scheuermittel. Keinesfalls darf die Reinigungs- bestimmt. Sie dürfen nicht bei besonders großem Staub- bzw. flüssigkeit in das Gerät gelangen. Die Anwendung STOP STOP Feuchtigkeitsgehalt der Luft, bei Explosionsgefahr sowie bei...
Bezeichnung der Bedienelemente Bezeichnung der Bedienelemente Gerätefrontseite Geräterückseite VOLT Spannungsanzeige AMP. Stromanzeige Strombegrenzung, Überstrom- anzeige 230 V / 50 - 60 Hz FUSE IEC 127-III 5 x 20 T2.5A time lag, träge, temporisé, lento ...
Netzgeräte-Grundlagen Netzgeräte-Grundlagen Sekundär getaktete Schaltnetzteile erhalten ihre Eingangs- spannung für den Schaltregler von einem Netztransformator. Diese wird gleichgerichtet und mit entsprechend größeren Kapa- zitäten gesiebt. Netz- Schalt- Lineare Netzteile Transformatór Gleichrichter Transistor Filter Linear geregelte Netzteile besitzen den Vorzug einer sehr kon- Ausgang stanten Ausgangsspannung, selbst bei starken Netz- und Last- Wechsel-...
Um einen angeschlossenen empfindlichen Verbraucher im Fehler- kein Muss. Der maximal mögliche Gesamtstrom ist die Summe fall noch besser vor Schaden zu schützen, besitzt das HM 7042-4 der Einzelströme der parallel geschalteten Quellen. eine elektronische Sicherung. Im Fehlerfall schaltet diese, inner- halb kürzester Zeit nach Erreichen von I...
HM 7042-4 kann die Schutzkleinspannung von 42 V immer zuerst die benötigte Ausgangsspannung eingestellt wer- überschritten werden. Beachten Sie, dass in diesem den. Danach werden die Ausgänge des HM 7042-4 mit OUTPUT Fall das Berühren von spannungsführenden Teilen ALL CHANNELS zugeschaltet.
Bedienelemente und Anzeigen Bedienelemente und Anzeigen 0-32V / 2A 0-5,5V / 5A Ausgangspannung regelbar von 0-32V. Sicherheitsbuchsen für Ausgangspannung regelbar von 0 - 5,5 V. Sicherheitsbuchsen für 4mm-Sicherheitsstecker. Die Ausgangsspannung ist dauernd 4mm-Sicherheitsstecker. Die Ausgangsspannung ist dauernd kurzschlussfest. kurzschlussfest. ...
Seite 13
Der Kurzschluss des Aus- gangs wird nun entfernt. ELECTRONIC FUSE wird betätigt. Die LED [ON] leuchtet. Das HM 7042-4 befindet sich im Modus elektronische Sicherung. Wird jetzt der Grenzwert I eines Ausganges erreicht, werden alle Ausgänge gleichzeitig abge- schaltet.
In the vicinity of strong magnetic or/and electric fields even a careful measuring set-up may not be sufficient to guard against the intrusion of undesired signals. This will not cause destruction or malfunction of HAMEG instruments, however, small deviations from the guranteed specifications may occur under such conditions.
Seite 15
Switched-mode power supplies (SMPS) ........ Parallel and series operation ..........Current limiting ..............Electronic fuse ..............Concept of the HM 7042-4 ............ Introduction to the operation of the HM 7042-4 ..... Survey of controls and displays ..........Subject to change without notice...
LED. In order to protect sensitive loads or such loads which require multiple The HM 7042-4 known and proven for many years will continue voltages an electronic fuse is provided which if activated switches to serve our customers in the future.
Specifications Specifications Valid at 23 degrees C after a 30 minute warm-up period. Miscellaneous Outputs Protection class: I acc. to EN 61010 (IEC 61010) 2 x 0-32 V + 0..5,5 V On/off pushbutton control. with protective earth SMPS followed by a linear regulator with overtemperature protection.
If the feet are not used the instrument can be combined with – The line voltage of the instrument must correspond to the many other HAMEG instruments. line voltage used. – Opening of the instrument is allowed only to qualified...
Warranty Check fuse holder and line cord for any damages. Use a suitable HAMEG instruments are subject to a strict quality control. All screw driver of appr. 2 mm to depress the plastic fuse holder instruments are burned in for 10 hrs prior to shipment. By releases on both sides, the housing is marked where the screw intermittent operation almost all early failures are detected.
Basics of power supplies Basics of power supplies mains switching transformer transistor rectifier filter output Linear power supplies voltage Linear regulated power supplies excel by their highly constant voltage output voltage, low ripple and fast regulation, even under high line control and load transients.
Electronic fuse In order to provide a still better protection than current limiting Turning on the HM 7042-4 offers the HM 7042-4 features an electronic fuse. As soon as I After turning on all outputs will remain disabled, protecting the ...
Survey of all operating controls and displays Survey of all operating controls and displays 0 – 5.5 V / 5 A 0 – 32 V / 2 A This output voltage can be adjusted 0 – 5.5 V. 4 mm safety Output voltage, adjustable 0 –...
Seite 24
has to be removed. Then Electronic Fuse is depressed, the LED [ON] will light up indicating that the HM 7042-4 is in the Electronic Fuse mode. In this mode all outputs will be immediately deactivated if the I of one channel is reached. In order to leave this mode ...
Seite 25
Survey of all operating controls and displays Subject to change without notice...