Receiver Installation (Arf Plus); Transmitter Setup (Bnf Basic) - Horizon Hobby E-Flite Viper 90mm EDF Bedienungsanleitung

EN

Receiver Installation (ARF Plus)

The Spektrum AR637T receiver is recommended for ths airplane. If you choose to install
another receiver, ensure that it is at least a 6-channel full range (sport) receiver. Refer to
your receiver manual for correct installation and operation instructions.
Installation (AR637T shown)
1. Mount the receiver parallel to the length of the fuselage as shown. Use heavy
duty double-sided servo tape.
NOTICE: Incorrect installation of the receiver could cause a crash.
2. Attach the appropriate control surfaces to the their respective ports on the
receiver using the chart in the illustration.
AR637 Port Assignments
BND/PRG = BIND 4 = Rudder
1 = Throttle 5 = Retracts
2 = Ailerons 6 = Flap
3 = Elevator

Transmitter Setup (BNF Basic)

IMPORTANT: After you set up your model, always rebind the transmitter and
receiver to set the desired failsafe positions.
The GEAR Channel (CH 5) controls the retractable landing gear. If you are using a 6
channel transmitter, The FLAP Channel (CH 6) can be used to toggle SAFE Select.
With the values listed below it will turn SAFE on for half and full lap positions and
AS3X will be on for no laps position.
To use the lap channel for the SAFE Select switch the values must be set to
+100 and -100 and the speed set to 0 temporarily to assign the safe switch in the
lap system menu. Then change the lap systems values back to the listing in the
TX setup. See the SAFE Select Switch Designation section of this manual to assign
the switch for SAFE Select.
Dual Rates
Attempt your irst lights in low rate. For landings, use high rate elevator.
NOTICE: To ensure AS3X technology functions properly, do not lower rate values
below 50%. If less control delection is desired, manually adjust the position of
the pushrods on the servo arm
NOTICE: If oscillation occurs at high speed, refer to the Troubleshooting Guide
for more information.
Exponential
After irst lights, you may adjust expo in your transmitter.
† Some of the terminology and function locations used in the iX12 and iX20
programming may be slightly different than other Spektrum AirWare
The names given in parentheses correspond to the iX12 and iX20 programming
terminology. Consult your transmitter manual for speciic information about
programming your transmitter.
* Flap programming values may vary slightly. For your initial lights use
the recommended lap travel settings, and adjust the lap travel to your
preference on subsequent lights.
6
radios.
™
www.modellmarkt24.ch www.modellmarkt24.ch
Computerized Transmitter Setup
Start all transmitter programming with a blank ACRO model (perform a model reset),
then name the model.
Set Dual Rates to
Set Servo Travel to
Set Throttle Cut to
Set Retract Channel to
Set Aileron Expo to High Rate 10%
Set Elevator Expo to High Rate 10%
Set Rudder Expo to High Rate 10%
DXS Refer to spektrumrc.com for the appropriate download setup.
1. Go to the SYSTEM SETUP
2. Set MODEL TYPE: AIRPLANE
3. Set WING TYPE: 1 AIL; 1 FLP
4. Set FLAP SYSTEM: Choose Flap
DX7S
POS 0:
DX8
POS 1:
POS 2: -100% FLAP*
Switch: SWITCH D
Speed: 2.0S
1. Go to the SYSTEM SETUP
DX6e
2. Set MODEL TYPE: AIRPLANE
DX6 (Gen2)
DX7 (Gen2)
3. Set AIRCRAFT TYPE
DX8e
WING: 1 AIL; 1 FLP
DX8 (Gen2)
4. Set CHANNEL ASSIGN (Model Setup, Channel Assign)
DX9
(Default switch assignments with a new model setup)
DX10t
Gear (CH5): SWITCH A
DX18
DX20
5. Set FLAP SYSTEM:
iX12
Switch: SWITCH D
iX20
POS 0:
NX6
POS 1:
NX8
POS 2: -100% FLAP* -5% ELEVATOR
NX10
Speed: 2.0S
Viper 90mm EDF
HIGH 100% LOW 70%
100%
-100%
Reverse
Low Rate 5%
Low Rate 5%
Low Rate 5%
100% FLAP* 0% ELEVATOR
0% FLAP* -3% ELEVATOR
-5% ELEVATOR
(Model Utilities)
†
:
(Model Setup, Aircraft Type) †
100% FLAP* 0% ELEVATOR
0% FLAP* -3% ELEVATOR
:
†