Electrolux Flymo XL 500 Bedienungsanleitung Seite 5

Wheel Frame (if applicable)
Zum Radgestell gehörende Teile
(falls zutreffend)
Chariot de transport (s'il y a lieu)
Wielframe (indien van toepassing)
Hjulramme (om relevant)
Pyörän runko (jos käytössä)
Hjulram (där sådan finns)
Hjulstel (hvis relevant)
Bastidor de las ruedas (si fuera
aplicable)
Armação das Rodas (se aplicável)
Telaio ruote (se in dotazione)
Fitting the Lower Handle to the Lawnmower
1. Feed the hook (A2) attached to the lower handle
(A1) halfway through the centre slot of the guide
(A3), in the direction indicated by the arrow (A4).
2. Maintaining the hook (A2) in the centre slot of the
guide (A3) turn the lower handle (A1) clockwise
through 90 0 to place both legs of the lower handle in
position between the hood brackets (A5).
3. Insert the pins (B1) and secure with the retaining
clips (B2).
1. Fit the lower handle (E1) to the deck with the lower
handle pin (E2) as illustrated in Fig E.
2. Attach the wheels (F1) to the wheel frame (F2) with the
wheel retaining clips (F3) as illustrated in Fig F.
3. Fit the wheel frame (G1) to the deck with the lower
handle bolt (G2), small washer (G3), large washer
The handle position can be adjusted using the guide
and hook assembly.
1. Lift hook (C1).
Use a fresh, clean, unleaded regular automotive
gasoline Do not fill the fuel tank in an enclosed area,
when the engine is hot or while you are smoking or near
a naked flame. Thoroughly clean around the fuel tank
filler cap before filling, this will help to prevent dirt being
introduced into the fuel system. Fuel should be stored
in a cool place away from naked flames. Do not fill the
tank while the engine is running. Fill the fuel tank
through a funnel fitted with a fine filter. Never fill fuel
tank completely, only fill to the base of the filler neck.
When filling the fuel tank from empty, or when the
engine has previously run dry, a minimum of 400cc of
fuel must be added (to the level of the line indicated
in the diagram) to ensure correct priming of the fuel
pump to start the engine. Your carburettor is pre-set.
Normally no further adjustment is required.
Use 4-stroke automotive detergent oil. SAE 10W-30
is recommended for general use.
22
31
30
32
33
Assembly (without wheels)
Fitting the Upper Handle to the Lower Handle
BEFORE fitting the upper handle to the lower handle,
stabilize the lower handle by lifting the hook (C1) to the
'parking' position (C2).
1. Ensure the Choke Control Lever is on the left hand
2. Align the lower and upper handle (See fig D).
3. Fit the cables to the handles with the cable ties
Assembly (with wheels)
4. Locate the lower telescopic tubes (H1) inside the upper
Fit the Upper Handle to the Lower Handle by following the
instructions above in 'Assembly (without wheels)' section.
Handle Position
2. Position as required:
Fuel
Oil
Fill with oil as instructed in your Engine Owners
Manual provided with your product.
21
23
25
26
29
34
side when viewed from the rear.
Locate the bolts (D1), washers (D2) and secure with
the handle knobs (D3).
provided, making sure the cables are not trapped
between the upper and lower handles.
(G4) and locknut (G5) as illustrated in Fig G.
telescopic tubes (H2) and secure with the pin (H3) and
retaining clip (H4) as illustrated in Fig H.
(C2)
Parking position
(C3)
Mowing position
24
27
28
ENGLISH - 1