cam Panoramic Gebrauchsanweisungen Seite 20

PANORAMIC-marzo 2020_Layout 1 16/03/20 11:48 Pagina 20
INSTRUCTIONS FOR USE
4k. Pull the straps tight by the harness
adjustment strap, and make sure the
tightness is comfortable to your kid. Do
not twist or interchange the harness
straps.
4l. Pull the strap end straight towards
you, not upwards or downwards. Please
pay attention to the strap end.
4m. For the safety of your baby, please
check that the harness straps of the car
seat are comfortable but firm fit around
your child; the harness straps are
adjusted correctly; the harness straps
are not twisted; the buckle tongues are
engaged in the harness buckle.
Installation of Group 0+ (birth-13kg),
with ISOFIX and Top tether.
First please check if there are 2 ISOFIX
anchoring in
intersection of the vehicle seat beck and
seat cushion, and the user-ready top
tether anchoring behind the vehicle seat.
The user-ready top tether anchorage is
usually permanently installed on the
inner rear luggage shelf or on the vehicle
floor. For more details you could read
your vehicle guidelines or contact the
vehicle manufacturer.
5a. Rotate by pressing the rotation
button and turn the seat into the
rearward position.
5b. Press the ISOFIX release button and
push the ISOFIX connectors forward as
far as possible.
5c. Push the ISOFIX connectors directly
into the anchorages until you hear an
audible sound "click".
5d. Press the rotation button and turn
the seat against the direction of travel,
as rearward facing position. Grasp the
recline button and press the child seat
into the most reclined position. If the
ISOFIX connectors are correctly installed,
the release button will pop out, and you
can see a clear green mark on it. Grasp
the seat body to check the seat if it is
fastened tightly or shakes. If the seat
shakes and the ISOFIX connectors are
pulled out, please repeat the above
steps and install again.
5e-5f. The top tether strap should go
through the blue clips on both sides,
then lock the hook on the anchor
19
the perpendicular
bracket. Pull the tether strap on the
other end back to tighten and top tether.
5g. Pull out the top tether and press the
tether strap release button to extend the
strap until it is long enough to hook
onto the user-ready tether anchorage
behind.
5h. Hook the tether strap hook onto the
user-ready anchorages. There maybe 3
anchorages for the hook, please find one
in your convenience.
5i. If the top tether is tightened
correctly, a green mark will show up on
the other end of the strap release
button, please check it.
6a. Turn the car seat in forward facing
position.
6b. Press the ISOFIT release button and
push the ISOFIT connectors forward as
far as possible.
6c. Push the recline button and put the
child seat into a comfortable reclined
position (the seat can be reclined in 3
positions ) before installing the whole
child seat.
6d. Push the ISOFIT connectors directly
into the anchorages until you hear an
audible sound "click".
6e. Put the vehicle seatbelt through the
front of the seat of the car and the
shoulder belt through
bracket.
6f. Check that the car seat body is
securely tightened.
If the seat is shaking and the ISOFIT
connectors are not correctly fitted,
please repeat the above steps and install
it again.
6g. Pull the Tether strap on the other
end back to tighten to the Top tether.
6h. Hook the tether strap hook onto the
user-ready anchorages. There maybe 3
anchorages for the hook, please find one
in your convenience.
6i. If the top tether is tightened
correctly, a green mark will show up on
the other end of the strap release
button, please check it.
Removing the 5-points
system and insert cushion for Group
2/3.
7a. Press and hold the central adjuster,
losen the harness straps as far as you
the buckle
harness