Troubleshooting Guide; Warranty; Technical Data; Vibration Value - Kärcher BCU 260/36 Bp Bedienungsanleitung

3. Pull the string reel off the support and dispose of it
properly.
4. Possibly. wind a cutting string on the new string reel.
5. Fit the string reel in the support.
Malfunctions often have simple causes that you can
remedy yourself using the following overview. When in
doubt, or in the case of malfunctions not mentioned
here, please contact your authorised Customer Service.
Fault
The device does not start
up
The device stops during
operation

Warranty

The warranty conditions issued by our relevant sales
company apply in all countries. We shall remedy possi-
ble malfunctions on your appliance within the warranty
period free of cost, provided that a material or manufac-
turing defect is the cause. In a warranty case, please
contact your dealer (with the purchase receipt) or the
next authorised customer service site.
(See overleaf for the address)

Technical data

Device performance data
Working voltage of the battery
Working width of brushcutter
Working width of string trimmer
Cutting string, diameter
Max. Speed (± 100), brushcutter /
string trimmer
Brushcutter: Determined values according to
EN ISO 11806-1
Sound pressure level L
pA
Uncertainty K
pA
Sound power level L + K uncer-
WA
tainty
WA
Right handle hand-arm vibration
value
Left handle hand-arm vibration
value
Uncertainty K
String trimmer: Determined values in acc. with
EN 50636-2-91
Sound pressure level L
pA
18

Troubleshooting guide

Cause
Battery pack is not inserted correctly.
Battery pack is empty
Battery pack is defective.
Cutting head blocked by cutting residue  Remove the cutting residue.
Motor is overloaded
Motor has overheated
The battery has overheated
BCU
260/36
Bp
V 36
mm 260
mm 380
mm 1.65
/min 5600
dB(A) 77.0
dB(A) 3.0
dB(A) 94
2
m/s 1.3
2
m/s 3.6
2
m/s 1.5
dB(A) 80.5
6. Fit the string reel cover in the support. Take care to
ensure that the string reel cover audibly latches into
place.
As the battery pack ages, even if it is looked after, its ca-
pacity reduces such that the full run time will no longer
be reached when fully charged. This does not indicate a
defect.
Rectification
 Push the battery pack into the mounting
until it latches into place.
 Charge the battery pack.
 Replace the battery pack.
 Mow only suitable cutting material, see
Chapter Intended use.
 Stop working and allow the motor to cool
down.
 Stop working and allow the battery to cool
down to normal battery temperature.
Uncertainty K
pA
Sound power level L
tainty
WA
Right handle hand-arm vibration
value
Left handle hand-arm vibration
value
Uncertainty K
Dimensions and weights of brushcutter
Length x width x height
Weight (without battery pack)
Dimensions and weights of string trimmer
Length x width x height
Weight (without battery pack)
Subject to technical modifications.

Vibration value

WARNING
The specified vibration value was measured using a
standard test procedure and may be used to compare
devices.
The specified vibration value may be used in a provi-
sional assessment of the load.
Depending on the way the device is used, the vibration
emission can deviate from the specified overall value
during the current use of the device.
Device with a hand-arm vibration value >
2.5 m/s² (see chapter Technical Data in the
English
dB(A)
+ K uncer- dB(A)
WA
2
m/s
2
m/s
2
m/s
mm
kg
mm
kg
BCU
260/36
Bp
3.0
95
3.5
6.3
1.5
1804 x 6
44 x 364
4.2
1767 x 6
44 x 428
4.3