Makita KP0800 Bedienungsanleitung Seite 10

Nozzle cleaning
Clean the nozzle regularly.
Use a compressed air to clean the clogged nozzle.
OPERATION
WARNING:
To reduce the risk of injury to
persons, do not operate without nozzle or chip
cover in place.
Hold the tool firmly with one hand on the knob and the
other hand on the switch handle when performing the
tool.
Planing operation
► Fig.15: 1. Start 2. End
First, rest the tool front base flat upon the workpiece
surface without the blades making any contact. Switch
on and wait until the blades attain full speed. Then
move the tool gently forward. Apply pressure on the
front of tool at the start of planing, and at the back at the
end of planing. Planing will be easier if you incline the
workpiece in stationary fashion, so that you can plane
somewhat downhill.
The speed and depth of cut determine the kind of finish.
The power planer keeps cutting at a speed that will not
result in jamming by chips. For rough cutting, the depth
of cut can be increased, while for a good finish you
should reduce the depth of cut and advance the tool
more slowly.
Shiplapping (Rabbeting)
► Fig.16
To make a stepped cut as shown in the figure, use the
edge fence (guide rule) which is obtained as accessory.
► Fig.17: 1. Blade edge 2. Cutting line
Draw a cutting line on the workpiece. Insert the edge
fence into the hole in the front of the tool. Align the
blade edge with the cutting line.
► Fig.18: 1. Screw 2. Edge fence (Accessory)
Adjust the edge fence until it comes in contact with the
side of the workpiece, then secure it by tightening the
screw.
► Fig.19
When planing, move the tool with the edge fence flush
with the side of the workpiece. Otherwise uneven plan-
ing may result.
Maximum shiplapping (rabbeting) depth is 9 mm.
► Fig.20
You may wish to add to the length of the fence by
attaching an extra piece of wood. Convenient holes
are provided in the fence for this purpose, and also for
attaching an extension guide (optional accessory).
Chamfering
► Fig.21
► Fig.22
To make a chamfering cut as shown in the figure, align
the "V" groove in the front base with the edge of the
workpiece and plane it.
MAINTENANCE
CAUTION:
• Always be sure that the tool is switched off and
unplugged before attempting to perform inspec-
tion or maintenance.
• Never use gasoline, benzine, thinner, alcohol
or the like. Discoloration, deformation or cracks
may result.
Sharpening the planer blades
For conventional blades only
► Fig.23: 1. Sharpening holder
Always keep your blades sharp for the best perfor-
mance possible. Use the sharpening holder (optional
accessory) to remove nicks and produce a fine edge.
► Fig.24: 1. Wing nut 2. Blade (A) 3. Blade (B) 4. Side
(D) 5. Side (C)
First, loosen the two wing nuts on the holder and insert
the blades (A) and (B), so that they contact the sides
(C) and (D). Then tighten the wing nuts.
► Fig.25
Immerse the dressing stone in water for 2 or 3 minutes
before sharpening. Hold the holder so that the both
blades contact the dressing stone for simultaneous
sharpening at the same angle.
Replacing carbon brushes
► Fig.26: 1. Limit mark
Remove and check the carbon brushes regularly.
Replace when they wear down to the limit mark. Keep
the carbon brushes clean and free to slip in the holders.
Both carbon brushes should be replaced at the same
time. Use only identical carbon brushes.
► Fig.27: 1. Chip cover 2. Screwdriver
► Fig.28: 1. Nozzle 2. Screwdriver
Use a screwdriver to remove the chip cover or nozzle.
► Fig.29: 1. Brush holder cap 2. Screwdriver
Use a screwdriver to remove the brush holder caps.
Take out the worn carbon brushes, insert the new ones
and secure the brush holder caps.
To maintain product SAFETY and RELIABILITY, repairs,
any other maintenance or adjustment should be per-
formed by Makita Authorized Service Centers, always
using Makita replacement parts.
10 ENGLISH