REMS Serie Collum RG Betriebsanleitung Seite 9

g
customer service workshop in case of damage.
cient cable cross-section. Use extension leads with a cable cross-section of
at least 2.5 mm².
the machine when they are over 16, when this is necessary for their training and
when they are supervised by a trained operative.
responsible person. Otherwise there is a risk of operating errors and injuries.
WARNING
Danger with a medium degree of risk which could result in
death or severe injury (irreversible) if not heeded.
Danger with a low degree of risk which could result in minor
injury (reversible) if not heeded.
NOTICE
Material damage, no safety note! No danger of injury.
Read the operating manual before starting
Use for the intended purpose
WARNING
REMS roller groove device, REMS Collum RG (all models), REMS Magnum RG (all
models) are intended for grooving pipes for pipe coupling systems. All other uses
are not for the intended purpose and are therefore prohibited.
1.1. Scope of Supply
REMS roller groove device: Roller groove device, grooving rollers 2 – 6" pair,
Allen key, instruction manual.
REMS Collum RG: Roller groove device, electric die stock, support,
2 cylinder-head screws M 8 × 25, adapter,
washer, cylinder-head screw M 8 × 16, grooving
rollers 2 – 6" pair, Allen key, instruction manual.
REMS Magnum RG: Roller groove device, roller groove machine,
grooving rollers 2 – 6" pair, Allen key, instruction
manual.
REMS roller groove device for REMS Tornado, REMS Magnum,
REMS Amigo, REMS Amigo 2, REMS Amigo 2 Compact
Roller groove device R 300 for Ridgid 300
Roller groove device R 535 for Ridgid 535
Roller groove device N80A for Rex/Rothenberger/Super-Ego N80A 347003
Roller groove device Delta 4 for Rex Delta 4"
Grooving rollers 1 – 1½", pair
Grooving rollers INOX 1 – 1½", pair
Grooving rollers 2 – 6", pair
Grooving rollers INOX 2 – 6", pair
Grooving rollers 8 – 12", pair
Grooving rollers INOX 8 – 12", pair
Grooving rollers Cu 54 – 159 mm, pair
REMS Amigo drive unit
REMS Amigo 2 drive unit
REMS Amigo 2 Compact drive unit
Base frame for REMS Collum RG
Wheel set for base frame REMS Collum RG
Conversion kit Amigo / Amigo 2 / Amigo2 Compact
Safety foot switch for REMS Collum RG
Base frame for REMS Magnum RG
Base frame, mobile for REMS Magnum RG
REMS Jumbo, folding workbench
Conversion kit RG-T on L-T (for thread cutting)
REMS Herkules 3B
REMS CleanM
REMS gear grease
REMS hydraulic oil
1.3. Applications
Steel pipes
Stainless steel pipes, copper, aluminium, PVC pipes
Roller groove device,
with hydraulic hand pump
Magnum 2000 RG-T,
with hydraulic hand pump
Magnum 2010/2020 RG-T,
with hydraulic hand pump
-
Apprentices may only use
1.5. Weight
2. Start-up
2.1. Electrical connection
347000
347001
347002
347004
347030
347053
347035
347046
347040
347047
347034
530000
540000
540001
849315
849317
347007
347010
344105
344100
120200
340110
120120
140119
091012
091026
DN 25 – 300, 1 – 12"
(Magnum T Ø 250 mm)
L×W×H: 510×415×405 mm
(20"×16.3"×16")
L×W×H: 795×510×610 mm
(31.3"×20"×24")
L×W×H: 750×510×610 mm
(29.5"×20"×24")
REMS Collum RG
with hydraulic hand pump
REMS Collum RG 2
with hydraulic hand pump
REMS Collum RG 2 Compact
with hydraulic hand pump
REMS roller groove device
REMS Magnum 2000 RG-T, including roller groove device
REMS Magnum 2010 RG-T, including roller groove device
REMS Magnum 2020 RG-T, including roller groove device
REMS Collum RG
REMS Collum RG 2
REMS Collum RG Compact
Transport weights above 35 kg must be carried by at least 2 persons. When
transporting and installing the machine, please note that the machine has a
high centre of gravity with and wi hout the base frame, i.e. it is top heavy.
WARNING
Before connecting the REMS Collum RG,
REMS Collum RG 2, REMS Collum RG 2 Compact, REMS Magnum 2000
RG-T, REMS Magnum 2010 RG-T, REMS Magnum 2020 RG-T check that the
connect drive units of protection class I to a socket/extension lead with a
functional PE conductor. On building sites, in a wet environment, indoors and
outdoors or under similar installation conditions, only operate the electrical
device on the mains with a fault current protected switch (FI breaker) which
interrupts the power supply as soon as the leakage current to earth exceeds
30 mA for 200 ms.
See REMS Magnum instruction manual: The machine can be lifted at the front
by the guide arms (8) and at the rear by a pipe clamped into a quick-action
hammer chuck (1) and guide chuck (2) for transport.
Fix the machine to REMS Jumbo (accessory, Art. No. 120200) or one of the
base frames (accessory, Art. No. 344105, 344100) with the 4 screws provided.
Make sure that the machine is horizontal. Open the quick-action hammer chuck
(1). Push the roller grooving unit in the guide arms (8) until the drive shaft of
the roll grooving unit protrudes into the quick-action hammer chuck with its 3
faces. Close the quick-action hammer chuck until the clamping jaws are in
contact with the 3 faces of the drive shaft. With the clamping ring (9), tighten
the drive shaft after a brief opening movement with one or two hard turns.
See REMS Magnum instruction manual: Swing in the pipe cutter and the inner
pipe deburrer. Undo the wing screw on the clamping ring, Remove the oil pan
with the cuttings tray. Short circuit the mechanical lubricant pump by connec ing
the hose end detached from the tool holder to the intake side of the pump.
Lubricant must circulate inside the pump to prevent it from being damaged.
Remove the tool set. Make sure that the machine is horizontal.
Push the roller grooving unit in the guide arms (8) un il the drive shaft of the
roll grooving unit protrudes into the quick-action hammer chuck with its 3 faces.
Close the quick-action hammer chuck until the clamping jaws are in contact
with the 3 faces of the drive shaft. With the clamping ring (9), tighten the drive
shaft after a brief opening movement with one or two hard turns.
See REMS Magnum instruction manual: Swing in the pipe cutter and the inner
pipe deburrer. Undo the wing screw on the clamping ring, remove the cuttings
tray. Detach the hose end from the tool holder and insert in the hole in the
coolant tray so that lubricant can circulate inside the pump to prevent it from
being damaged. Remove the tool set. Always ensure that the machine is always
positioned horizontally on the mobile base frame. Remove wheels or place the
two stand pipes underneath.
Push the roller grooving unit in the guide arms (8) un il the drive shaft of the
roll grooving unit protrudes into the quick-action hammer chuck with its 3 faces.
Close the quick-action hammer chuck until the clamping jaws are in contact
with the 3 faces of the drive shaft. With the clamping ring (9), tighten the drive
shaft after a brief opening movement with one or two hard turns.
See REMS Tornado instruction manual: Swing in the pipe cutter and the inner
pipe deburrer. Undo the wing screw on the clamping ring, Remove the oil pan
with the cuttings tray. Short circuit the mechanical lubricant pump by connec ing
the hose end detached from the tool holder to the intake side of the pump.
Lubricant must circulate inside the pump to prevent it from being damaged.
g
L×W×H: 510×415×470 mm
(20"×16.3"×18.5")
L×W×H: 510×415×580 mm
(20"×16.3"×23")
L×W×H: 510×415×525 mm
(20"×16.3"×20.7")
26 kg
68 kg
80 kg
80 kg
32 kg
35 kg
33 kg