Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Getting started
Learn how to set the product up and turn it on. Log into the web interface and configure basic
settings: change the login default password and set the time.
a) Setting up and switching on
1. Plug the device into a mains socket.
2. Adjust the antennas as shown in the below images.
3. Switch on. Slide the ON/OFF switch to ON.
» The Power/WPS indicator lights up.
• To switch off, slide the ON/OFF switch to OFF. The Power/WPS indicator goes out.
b) Logging into the web interface
Requirements:
• The product is switched on.
• You have a management device (computer, tablet computer) available.
Default parameters
Web interface address
Default IP address
Default password
Default SSID (network name)
1. Bring the management device near the product.
2. Connect the management device to the product:
- Wireless: connect to the product SSID (network name). Unless changed, connect to the
default SSID.
- Wired: use a network cable and connect to the LAN socket.
3. Open the web interface:
- Open a web browser.
- Enter
http://ap.setup
into the address bar and start the search. The interface loads. This
takes some time.
- (If the interface fails to load) type the product IP address into the URL bar and start the
search. Unless changed, use the default IP address.
4. When the interface is loaded, select the desired inter-
face language.
5. Enter the password (unless changed, use the default
password). Log in.
» The status dashboard shows.
c) Configuring basics
Requirements:
• The product is switched on.
• You are logged into the web interface.
Changing the login password
1. Go to
Setup
> Login
Password. The password mask shows.
2. Enter the current password and define a new password.
3. Click
to change the password.
Apply
You can sign it again using the new password after refreshing the browser window.
Setting the time
1. Go to
Setup
> Time
Settings. The settings window opens.
2. Apply time settings:
- Select the time zone.
- Enable
if you wish to synchronize the time.
SYNC Time
3. Click
to save the changes.
Apply
What's next
Configure one of the operating modes: Repeater / Access Point (AP) / Router.
http://ap.setup
192.168.10.1
admin
Renkforce-2.4G
Use a strong password.
Repeater mode
In repeater mode, the product is connected to a router or access point (AP) and repeats its
WLAN signal to extend network coverage.
You connect network hosts (e.g. computer or smartphone) to the product using the product
SSID (network name) and the password set on the router or access point (AP).
Connecting the product
You can connect the product to a router or access point via WPS or manually.
After connecting, the product broadcasts (unless disabled) a new SSID (network name). By
default it uses the router/AP network SSID and appends a suffix in the form: SSID_EXT.
You can define your own SSID.
Requirements:
• The product is switched on.
• The product is close to the router/access point you want to connect to.
a) Using WPS
WPS (Wi-Fi Protected Setup) must be supported and enabled on the router or access point
you intend connect to.
Make sure you know how to use WPS on the router/access point.
NOTICE
Using WPS (Wi-Fi Protected Setup) can make your network vulnerable under certain
conditions. If in doubt ask a specialist for assistance.
Observe the diagram and connect:
1. Enable the WPS function on the router/access point you intend to connect to.
2. Slide the mode selector switch to Repeater.
3. Hold down the WPS button for 6 seconds, then release it.
» The Power/WPS indicator flashes quickly.
4. Start the WPS connection on the router/access point. Wait for the connection to complete
(this takes some time).
» On successful connection, some WLAN indicator lights are lit solid.
» The product SSID is changed to the router/access point SSID with suffix.
5. (Optional) Change the SSID (network name):
- Log into the web interface.
- Go to
. The settings window opens.
Wizard
- In the
Repeater SSID
field, overwrite the SSID with your own.
- Click
Connect
to save the changes.
b) Connecting manually
1. Slide the mode selector switch to Repeater.
2. Log into the web interface.
3. Go to
. The settings window opens.
Wizard
4. Configure the connection:
- Select the network of the router/access point or
select
Manually enter
and provide the network
details.
- Enter the network password of the router/access
point into the
Wi-Fi Password
- (Optional) In the
Repeater SSID
the SSID with your own.
5. Click
to complete the configuration.
Connect
» On successful connection, some WLAN indicator lights are lit solid.
» The product SSID is changed to the router/access point SSID with suffix or your own
SSID.
field.
field, overwrite
Werbung
Inhaltsverzeichnis
