Listening To The Radio - Makita MR001G Betriebsanleitung

● Never pull and/or drag the cord of the adapter. If
not, the radio may accidentally fall down, causing
injury to you or someone around you.
IMPORTANT:
● The mains adapter is used as the means of
connecting the radio to the mains supply. The mains
socket used for the radio must remain accessible
during normal use.
● In order to disconnect the radio, the mains adapter
should be removed from the mains outlet completely.
● Use the AC power adapter supplied with the product
or specified by Makita only.
● Do not hold the power supply cable and plug by your
mouth. Doing so might cause an electric shock.
● Do not touch the power plug with wet or greasy hands.
● Damaged or entangled cords increase the risk
of electric shock. If the cord is damaged, have it
replaced by our authorized service center in order to
avoid a safety hazard. Do not use it before repair.
● After use, always store AC power adapter out of the
reach of children. If Children play with the cord, they
may suffer injury.
Note:
When your radio has any interference in AM band by
its adapter, please move your radio away from its AC
power adapter over 30cm.

LISTENING TO THE RADIO

Scan tuning AM/FM
Note:
The FM antenna is built into the handle. When operating
the radio, please straighten the handle properly above
the radio to get better reception. For the AM band, rotate
the radio to get best signal as the AM antenna is built
into the radio.
1. Press the Power button to switch on your radio.
2. Press the Band button to select AM or FM radio mode.
3. Press the Scan button, the LCD display will flash
Scan symbol and the radio will search and stop
automatically when it finds a radio station. Press the
Scan button again to pick up the found station.
Note:
● A stereo symbol will appear on the display, if the
station found is a stereo station.
● The radio will continue to search next available
stations if you do not press Scan button again when
it finds a radio station.
4. Rotate the Tuning control knob to adjust the sound
level as required. The LCD display will show sound
level changes.
Note:
● While adjusting the volume, make sure the FM/AM
is NOT flashing on the screen.
● If AM/FM is flashing on the screen, it allows you
to tune the stations manually (see the section of
"Manual tuning – AM/FM" for more detail).
● The volume should not be too large. To prevent
possible hearing damage, do not listen at high
volume levels for long periods.
5. To switch off your radio press the Power button.
Manual tuning – AM/FM
1. Press the Power button to switch on your radio.
2. Press the Band button to select AM or FM radio
mode.
3. Press the Tuning control knob and you will see the
FM or AM is flashing on the display.
Note:
● FM/AM will flash approx. 10 seconds. Within this
period, only manual tuning is allowed.
● If volume adjustment is desired while FM/AM is
flashing, press the Tuning control knob to stop the
flash and you can rotate the Tuning control knob to
adjust sound level.
4. Rotate the Tuning control knob to tune to a station.
5. When the end of the waveband is reached your radio
will recommence tuning from the opposite end of the
waveband.
Presetting stations in AM/FM mode
There are 5 preset stations each for AM and FM radio.
They are used in the same way for each waveband.
1. Press the Power button to switch on your radio.
2. Press the Band button to select the desired
waveband. Tune to the required radio station as
previously described.
3. Press and hold the required preset button until radio
beeps. The preset number will appear on the display.
The station will be stored using the preset number.
Repeat this procedure for the remaining presets as
you wish.
4. Preset stations which have already been stored may
be overwritten by following the above procedure if
required.
Change Stereo to Mono
When the stereo FM station reception is weak, you can
improve it by pressing and holding the Mono button for
2 seconds. The sound is no longer in stereo and stereo
indicator disappears.
Recalling a preset in AM/FM mode
1. Press the Power button to switch on your radio.
2. Press the Band button to select AM or FM radio
mode.
3. Momentarily press the required Preset button, the
preset number and station frequency will appear on
the display.
9 ENGLISH