Operation - Makita DCL282F Betriebsanleitung

5. Spread the cloth part of the dust bag inside the
cleaner.
► Fig.12
6.
Close the front cover completely.
► Fig.13: 1. Front cover
Installing the paper filter
Use the dust stopper also when installing paper filter.
Be careful not to take the upper side for the lower side
by mistake because they are different each other.
► Fig.14: 1. Upper side of dust stopper 2. Lower side
of dust stopper
1. Unfold the entrance of the paper filter before
setting it on the dust stopper.
► Fig.15
2.
Insert the protrusion of the paper filter into the
lower groove on the dust stopper as shown in the figure.
► Fig.16: 1. Dust stopper 2. Lower groove 3. Paper
filter
3. There is no distinction between the upper and
lower sides of the paper filter. You may insert its pro-
trusion of any side into the lower groove of the dust
stopper.
► Fig.17: 1. Lower groove
4. Overlap the frame of dust stopper with that of the
paper filter.
► Fig.18
5. Place the dust stopper and the paper filter
together into the cleaner cavity in the same direction of
arrow on the dust stopper. Insert them all the way into
the slots in the cleaner cavity.
► Fig.19
6. Spread the container part of the paper filter inside
the cleaner.
► Fig.20
7.
Close the front cover completely.
► Fig.21: 1. Front cover

OPERATION

CAUTION:
Do not move your face close to
the air vent when operating the cleaner. If foreign
objects are blown into eyes, it may result in personal
injury.
Installing or removing the cleaner
attachment
CAUTION:
After installing attachment,
check if it is securely installed. If the attachment
is installed imperfectly, it may come off and cause
personal injury.
CAUTION:
Be careful not to hit your hand on
the wall etc. when removing the attachment.
When using attachment with lock
function
To install attachment, insert it to the suction inlet of the cleaner
until it clicks. Make sure that the attachment is locked.
► Fig.22: 1. Suction inlet 2. Attachment with lock
function 3. Hook
NOTE: When installing the attachment with lock
function, be sure to align the release button with
the hook on the attachment. If they are not aligned,
the wand will not be locked and may come off from
the cleaner.
To remove, pull the attachment while pushing the release button.
► Fig.23: 1. Release button 2. Attachment with lock function
When using attachment without lock
function
CAUTION:
To connect attachment without lock
function, twist and insert it in direction of the arrow
to secure the connection during use. To discon-
nect the attachment, twist and extract it also in
direction of the arrow. If the attachment is twisted in
the opposite direction, the capsule may become loose.
► Fig.24
Cleaning (Suction)
Nozzle
Attach the nozzle to clean off tables, desks, furniture,
etc. The nozzle slips on easily.
► Fig.25: 1. Nozzle
Nozzle + Extension wand (Straight pipe)
The extension wand fits in between the nozzle and the
cleaner itself. This arrangement is convenient for clean-
ing a floor in a standing position.
► Fig.26: 1. Cleaner body 2. Extension wand 3. Nozzle
Corner nozzle
Fit on the corner nozzle for cleaning corners and crev-
ices of a car or furniture.
► Fig.27: 1. Corner nozzle 2. Cleaner body
Corner nozzle + Extension wand
(Straight pipe)
In tight quarters where the cleaner itself cannot squeeze
in, or in high places hard to reach, use this arrangement.
► Fig.28: 1. Corner nozzle 2. Extension wand
3. Cleaner body
Cleaning without nozzle
You can pick up powder and dust without nozzle.
► Fig.29
For picking up dust on a floor in a standing position, it is
convenient to attach the extension wand to the cleaner.
► Fig.30: 1. Extension wand
13 ENGLISH