Technical Data; Noise/Vibration Information - Bosch EasyImpactDrive 12 Originalbetriebsanleitung

Technical data

Cordless impact
screwdriver
Article number
Rated voltage
– Setting 1 min
– Setting 2 min
Impact rate
– Setting 1 min
– Setting 2 min
Maximum torque, hard Nm
screwdriving applica-
tion according to
ISO 5393
Machine screw dia- mm
meter
Max. screw diameter mm
Tool holder
Weight according to
EPTA-Procedure
01:2014
Permitted ambient temperature
– while charging
– During operation and
storage
Recommended batter-
ies
Recommended char-
gers
(Limited performance
at temperatures < 0 °C)

Noise/vibration information

Noise emission values determined according to
EN 62841-2-2.
Typically, the A-weighted noise level of the power tool is: 88
dB(A); sound power level 99 dB(A). Uncertainty K = 3 dB.
Wear hearing protection!
Total vibration values a (triax vector sum) and uncertainty K
h
determined according to EN 62841-2-2:
Impact tightening of fasteners of the maximum capacity of
2
the tool: a <9,5 m/s , K=1,5 m/s
h
The vibration level and noise emission value given in these
instructions have been measured in accordance with a
standardised measuring procedure and may be used to com-
pare power tools. They may also be used for a preliminary
estimation of vibration and noise emissions.
The stated vibration level and noise emission value repres-
ent the main applications of the power tool. However, if the
power tool is used for other applications, with different ap-
plication tools or is poorly maintained, the vibration level
Bosch Power Tools
EasyImpactDrive 12
3 603 CD6 6..
V 12
-1
0–1400
-1
0–2800
-1
0–2400
-1
0–3300
100
M4–M12
6
¼" internal hexagon
kg 1.0
°C 0 to +35
°C –20 to +50
PBA 12V ...
GAL 12...
2
and noise emission value may differ. This may significantly
increase the vibration and noise emissions over the total
working period.
To estimate vibration and noise emissions accurately, the
times when the tool is switched off or when it is running but
not actually being used should also be taken into account.
This may significantly reduce vibration and noise emissions
over the total working period.
Implement additional safety measures to protect the oper-
ator from the effects of vibration, such as servicing the
power tool and application tools, keeping their hands warm,
and organising workflows correctly.
Assembly
Remove the battery from the power tool before carry-
u
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
Removing the battery (see figure A)
Use only the chargers listed in the technical data. Only
u
these chargers are matched to the lithium-ion battery of
your power tool.
Note: The battery is supplied partially charged. To ensure
full battery capacity, fully charge the battery in the charger
before using your power tool for the first time.
The lithium-ion battery can be charged at any time without
reducing its service life. Interrupting the charging process
does not damage the battery.
The lithium-ion battery is protected against deep discharge
by the "Electronic Cell Protection (ECP)". A protective circuit
switches the cordless dust extractor off when the battery is
drained.
Do not continue to press the On/Off switch after the
u
power tool has automatically switched off. The battery
can be damaged.
To remove the battery (5), press the release buttons (4) and
pull the battery downwards out of the power tool. Do not
use force to do this.
Follow the instructions on correct disposal.
Changing the Tool
Remove the battery from the power tool before carry-
u
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
Inserting the application tool (see figure B)
Pull the locking sleeve (2) forward, guide the application tool
(1) into the tool holder up to the stop and release the locking
sleeve (2) to lock the application tool.
Screwdriver bits (12) can be inserted using a universal bit
holder with ball catch (11).
English | 13
1 609 92A 5GN | (21.01.2020)