Working Advice - Bosch GEX 40-150 Professional Originalbetriebsanleitung

14 | English
Preselecting the orbital stroke rate
You can even preselect the orbital stroke rate during opera-
tion using the necessary orbital stroke rate preselection
thumbwheel (3).
1–2 Low orbital stroke rate
3–4 Medium orbital stroke rate
5–6 High orbital stroke rate
The required orbital stroke rate is dependent on the material
and the work conditions and can be determined using prac-
tical tests.
After working at a low orbital stoke rate for an extended
period, you should operate the power tool at the maximum
orbital stroke rate for approximately three minutes without
load to cool it down.
Sanding Plate Brake
An integrated sanding pad brake reduces the orbital stroke
rate when running without load to prevent scoring when the
power tool is placed on the workpiece.
If the no-load orbital stroke rate constantly increases over
time, this means that the sanding pad is damaged and must
be replaced, or that the sanding pad brake is worn. A worn
sanding pad brake must be replaced by an after-sales ser-
vice centre authorised to work with Bosch power tools.

Working Advice

Pull the plug out of the socket before carrying out any
u
work on the power tool.
Always wait until the power tool has come to a com-
u
plete stop before placing it down.
This power tool is not suitable for bench-mounted use.
u
It must not be clamped into a vice or fastened to a work-
bench, for example.
Sanding Surfaces
Switch the power tool on, place the entire sanding surface
against the surface of the workpiece and apply moderate
pressure as you move the sander over the workpiece.
The material removal rate and sanding result are primarily
determined by the choice of sanding sheet, the preselected
orbital stroke rate level and the contact pressure.
Only immaculate sanding sheets achieve good sanding per-
formance and make the power tool last longer.
Be sure to apply consistent contact pressure in order to in-
crease the lifetime of the sanding sheets.
Application
Intermediate lacquer sanding
Lacquer/varnish
Softwood
Hardwood
Veneer
Aluminium
Steel
1 609 92A 6HP | (01.04.2021)
Excessively increasing the contact pressure will not lead to
increased sanding performance, rather it will cause more
severe wear of the power tool and of the sanding sheet.
Do not use a sanding sheet for other materials after it has
been used to work on metal.
Use only original Bosch-sanding accessories.
Rough Sanding
Attach a coarse grit sanding sheet.
Apply only light pressure to the power tool so that it runs at a
higher orbital stroke rate and a higher material removal rate
is achieved.
Fine Sanding
Attach a fine grit sanding sheet.
You can reduce the sanding plate orbital stroke rate by
lightly varying the contact pressure or changing the orbital
stroke rate level; the random orbit motion will be retained.
Move the power tool with moderate pressure flat on the
workpiece in a circular motion or alternately along and
across it. Do not tilt the power tool in order to avoid sanding
through the workpiece, e.g. veneers.
Switch the power tool off after completing operation.
Polishing
For polishing weathered lacquers and redressing scratches
(e.g. acrylic glass), the power tool can be fitted with an ap-
propriate polishing tool, e.g. lambswool bonnet, polishing
felt or polishing sponge (accessory).
Select a low orbital stroke rate (level 1–2) when polishing in
order to avoid heating up the surface excessively.
Apply the polish to an area slightly smaller than the area
which you intend to polish. Using the appropriate polishing
tool, work in the polish with either linear or circular move-
ments and with moderate pressure.
Do not allow the polish to dry out on the surface; this may
damage the surface. Do not expose the surface which you in-
tend to polish to direct sunlight.
Clean the polishing tool regularly to ensure good polishing
results. Wash the polishing tools with mild detergent and
warm water; do not use thinning agents.
Application Table
The information in the table below is the recommended val-
ues.
The best method for determining the best combination while
sanding or polishing is practical experimentation.
Grit
(coarse/fine sanding)
120/400
40/80
40/240
60/320
240/320
80/240
60/240
Orbital stroke rate level
5/6
5/6
5/6
5/6
5/6
5
5
Bosch Power Tools