Herunterladen Inhalt Inhalt Diese Seite drucken

Caution; Warning - Pioneer PRS-D220 Bedienungsanleitung

Bridgeable two-channel power amplifier
Inhaltsverzeichnis

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 30

CAUTION

Never replace the fuse with one of greater
value or rating than the original fuse. Use of
an improper fuse could result in overheating
and smoke and could cause damage to the
product and injury including burns.
Use the supplied hexagonal wrench to tight-
en screws when fastening wires to the ter-
minal. The use of a long, commercially
available hexagonal wrench can cause
excessive torque to be applied possibly
resulting in damage to terminals and wires.
CAUTION
Diagram A - Proper
8
+
-
Ohm
Speaker
8
+
-
Ohm
Speaker
L+
R-
Pioneer
Amplifier
4 Ohm Bridged Mode
Do NOT install or use your Pioneer ampli-
fier by wiring speakers rated at 4 Ohm (or
lower) in parallel to achieve a 2 Ohm (or
lower) bridged mode (Diagram B).
Amplifier damage, smoke, and overheat-
ing could result from improper bridging.
The amplifier surface could also become
hot to the touch and minor burns could
result.
To properly install or use a bridged mode
for a two-channel amplifier and achieve a
4 Ω load, wire two 8 Ω speakers in paral-
lel with Left + and Right – (Diagram A) or
use a single 4 Ω speaker. For a four-chan-
nel amplifier, follow the speaker output
connection diagram for bridging as shown
on the back of your amplifier, and wire
two 8 Ω speakers in parallel to achieve a 4
Ω load or use a single 4 Ω speaker per
channel.
If you have any questions or concerns,
please contact your local authorized
Diagram B - Improper
4
+
-
Ohm
Speaker
4
+
-
Ohm
Speaker
L+
R-
Pioneer
Amplifier
2 Ohm Bridged Mode
Pioneer dealer or call Pioneer customer
service.

WARNING

• We recommend that you use the special red bat-
tery and ground wire [RD-228], which is sold
separately. Connect the battery wire directly to
the car battery positive terminal (+) and the
ground wire to the car body.
• Do not touch the amplifier with wet hands.
Otherwise you may get an electric shock. Also,
do not touch the amplifier when it is wet.
• For traffic safety and to maintain safe driving
conditions, keep the volume low enough so that
you can still hear normal traffic sound.
• Check the connections of the power supply and
speakers if the fuse of the separately sold battery
wire or the amplifier fuse blows. Detect the cause
and solve the problem, then replace the fuse with
another one of the same size and rating.
• To prevent malfunction of the amplifier and
speakers, the protective circuit will cut the power
supply to the amplifier (sound will stop) when an
abnormal condition occurs. In such a case, switch
the power to the system OFF and check the
connection of the power supply and speakers.
Detect the cause and solve the problem.
• Contact the dealer if you cannot detect the cause.
• To prevent an electric shock or short-circuit
during connection and installation, be sure to
disconnect the negative (–) terminal of the battery
beforehand.
• Confirm that no parts are behind the panel when
drilling a hole for installation of the amplifier. Be
sure to protect all cables and important equipment
such as fuel lines, brake lines and the electrical
wiring from damage.
• DO NOT allow amplifier to come into contact
with liquids due to, for example, the location
where the amplifier is installed. Electrical shock
could result. Also, amplifier and speaker damage,
smoke, and overheating could result from contact
with liquids. In addition, the amplifier surface
and the surface of any attached speakers could
become hot to the touch and minor burns could
result.
2

Werbung

Inhaltsverzeichnis
loading

Inhaltsverzeichnis