Ferm MSM1036 Bersetzung Der Originalbetriebsanleitung Seite 7

10. Always lock the different degree set-ups
before you start processing.
11. Only buy suitable saw blades with a number
of revolutions of at least 5.000 revolutions per
minute.
12. Only use the correct saw blade. Too small or
too big saw blades are extremely dangerous.
13. Regularly inspect the saw blade for any faults.
Replace the saw blade if necessary.
14. Grease the new saw blade and clean the
flanges before you assemble the new blade.
Then assemble the blade in the correct
direction and pull the flanges firmly using the
central bolt.
15. Only use original flanges. All other types are
not suitable.
16. Never work without the protective cap of the
saw blade.
17. The moving part of the protective cap must
also remain assembled.
18. Never grease the saw blade while it is
rotating.
19. Always keep your hands removed from the
track of the saw blades.
20. Never pick up the workpiece by grasping with
your hands along or behind the saw blade.
21. Ensure that the workpiece never touches
the saw blade before the machine has been
switched on.
22. Never process metal or stone sorts with this
machine.
23. Use support aids in order to support long
workpieces.
24. Never use the machine in a dangerous
environment, where inflammable gases or
fluids are present.
25. Never leave the machine unattended without
first disconnecting it from the mains voltage.
26. If you hear abnormal noises, try to trace them
or take the machine to a recognized fitter, or
repair company.
27. If a part is broken or damaged, replace it or
repair it immediately.
28. Never stand in the track of the saw blade but
stand to the left or the right of the saw bench.
29. Your hands must likewise be placed next to
the track of the saw blade.
30. Always use the feedstick to push the wood
through the saw.
31. Always place the wood at the front of the saw
bench and then push it further back.
32. For mitring only the adjustable guide must be
used and the fence must be removed.
33. Never use the fence as a linear measure for
cutting off beams.
34. If the saw blade is locked: first switch off the
machine before you attend to the fault.
35. Avoid workpieces hitting back in your direction
by taking the following measures:
• Always use sharp saw blades.
• Do not saw too small workpieces.
• Never release the workpiece before it has
been completely pushed through the saw.
• Always adjust the guide parallel to the
saw blade.
• Never remove the saw protection.
36. Before you continue sawing, ensure that you
are standing firmly and that your hands are in
the required position.
37. Never use thinners to clean the machine. Only
use a damp cloth for cleaning.
38. Do not use saw blades which are damaged or
deformed.
39. Replace table insert when worn.
40. Use only saw blades recommended by the
manufacturer.
41. Take care that the selection of the saw blade
depends on the material to be cut.
42. Connect radial saws to a dust-collecting
device when sawing.
43. Use and correct adjustment of the riving knife
44. Use and correct adjustment of the upper saw
blade quard.
45 The dust that is emitted when sawing certain
types of wood can be toxic, i.s. oak, birch,
ash, beech and fibreboard. Certain dust, from
tropical wood types such as rosewood, coco
bolo and afzelia, cause cancer when breathed
in regularly. Ensure therefore that you have
good dust suction installed with a device that
fulfils the following requirements:
• Tube must fit perfectly on the connection
element
• Suction volume must be larger than 550
m3 per hour
• Vacuum at connection more than 740 Pa
• Air speed at connection more than 20
meters/second
Ensure that the least possible wood dust
is released in the atmosphere. WIPE wood
dust away (do not blow away with pressured
air), repair leaks in the tubes and ensure
appropriate ventilation.
Do not use saw blades which are damaged or
deformed.
Always clamp or press the workpiece firmly
EN
7