Herunterladen Inhalt Inhalt Diese Seite drucken

Service & Maintenance; Spare Parts - Belle RTX-Serie Bedienungshandbuch

Inhaltsverzeichnis

Werbung

Verfügbare Sprachen

Verfügbare Sprachen

Maintenance
The Altrad Belle RTX Range is designed to give many years of trouble free operation. It is, however, important that the simple regular
maintenance listed in this section is carried out.
It is recommended that an approved Altrad Belle dealer carries out all major maintenance and repairs. Always use genuine Altrad Belle
replacement parts, the use of spurious parts may void your warranty.
Before any maintenance is carried out on the machine, switch off the engine. If working on a petrol engined machine, disconnect the
HT lead from the sparkplug.
Always set the RTX on level ground to ensure any fl uid levels will be correctly read. Only use recommended oils (see chart).
Servicing the Engine
Service the engine according to the engine manufacturer's specifi cations. Refer to the engine operation and maintenance manual.
Every 8 Hours or Daily
1. Check for loose bolt and nuts, retighten if necessary.
2. Check and clean air fi lter element, re-lube the element according
to the engine manufacturer's recommendations. If operating
conditions are unusually dusty and severe, fi lter element cleaning
should be done more frequently.
3. Check oil level in crankcase of engine and replenish as necessary.
Check oil level in the ramming cylinder as per following procedures.
3a. Make sure that the machine has not been run in the last 10
minutes.
3b. Set the machine on a level surface and remove the oil plug.
3c. The top surface of the oil must be seen just below the lower rim of
the hole for oil plug. Replenish as necessary.
NOTICE: Care should be taken not to overfi ll the ramming cylinder
with oil. Overfi lling will cause excessive load on the engine, which
may result in poor or irregular vibration.
First 20 Hours of Operation
1. Replace the Oil in the Ramming Cylinder
Every 50 Hours or Weekly
2. Check for loose Bolts and Nuts. Retighten if necessary.
Every 200 Hours.
3. Change the Ramming Cylinder Oil. Do not overfi ll.
Fuel and Lubricant
Model
Fuel
Type of Oil
RTX50
RTX60
Unleaded
RTX66
Petrol
RTX68
RTX74
KEY
USE
LOCTITE
For information regarding Spare Parts availability for this machine, please visit www.Belle247.com or contact the ALTRAD Belle using
the following contact details:-
Tel:- +44 (0)1298 84606
Service & Maintenance
Capacity
Type Of Oil
2.5 Litres
10W-30,
2.5 Litres
API,
2.5 Litres
SF/CC,
2.5 Litres
SF/CC,
2.5 Litres
CD

Spare Parts

Fax:- +44 (0)1298 84722
Red Dot indicates
Minimum Oil Level
Engine Crankcase
Engine
Capacity
GX100
0.6 Litres
GX100
0.6 Litres
GX120 K1
0.6 Litres
GX100
0.6 Litres
GX120K1
0.6 Litres
USE
OIL
Email:- sales@ALTRAD-Belle.com
13
Ramming Cylinder
Type Of Oil
Capacity
10W-30,
0.7 Litres
API,
0.7 Litres
SF/CC,
0.8 Litres
SF/CC,
0.8 Litres
CD
0.8 Litres
USE
SILICONE
GB

Werbung

Kapitel

Inhaltsverzeichnis
loading

Verwandte Produkte für Belle RTX-Serie

Diese Anleitung auch für:

Rtx 50Rtx 60Rtx 66Rtx 68Rtx 74

Inhaltsverzeichnis