Cleaning And Maintenence; Environment; Trouble Shooting - MaxPro PROFESSIONAL MPAG950/125Q Bedienungsanleitung

Buffing
1.Remove the guard
2.Mount a buffing disc.
3.Turn on the device and allow it to run without applying a load.
4.Buff the surface using uniform circular movements.
Cut-off grinding
Risk of injury!
When using cutting discs, splinters may come away from the cutting disc during cutting and spin off. When
cutting, we recommend use the special protective cover.
High risk of injury!
Fragments of cut-off discs may be projected at a very high velocity.
- Do not apply any lateral pressure to the disc as the cut-off disc may tilt and burst.
1.Remove the protective special cover
2.Attach the protective cover
3.Mount a cut-off disc.
4.Turn on the device and allow it to run without applying a load.
5.Hold the motor block at an angle of 300 to 450 to the work piece.
6.Slowly and evenly run the disc along the designated cut-off line.
CLEANING AND MAINTANCE
Before any work on the machine itself, pull the mains plug. For safe and proper working, always keep the
machine and ventilation slots clean. In extreme working conditions, conductive dust can accumulate in
the interior of the machine when working with metal. The protective insulation of the machine can be
degraded. The use of a stationary extraction system is recommended in such cases as well as frequently
blowing out the ventilation slots and installing a residual current device (RCD). Please store and handle
the accessory(-ies) carefully. If the machine should fail despite the care taken in manufacturing and testing
procedures, repair should be carried out by an after-sales service centre for Maxpro power tools.

ENVIRONMENT

Do not dispose of electric tools, accessories and packaging together with household waste material -
in observance of European Directive 2002/96/EC on waste of electric and electronic equipment and its
implementation in accordance with national law, electric tools that have reached the end of their life must
be collected separately and returned to an environmentally compatible recycling facility.

TROUBLE SHOOTING

Fault Symptom Possible Cause
Out of service Disconnection between plug and
power socket
shortcircuit in power supply
At switch-off
Loose switching contact
Damage in soft starting block
Burnout of stator or rotor coil
Stator wiring disconnection
8
Troubleshooting
Put plug in power socket
Repair and reconnection
Switch on
Replace switchboard by repairer
Replace soft starting block by repairer
Replace stator or rotor by repairer
Reconnection by repairer
GB
Disconnection between carbon brush
and commutator
Sluggish start-up, falling short Unsmooth running in mechanical
of running speed part
Low supply voltage
Burnout of switch contact
Excessive sparkling during Underpressure in carbon brush spring Replace carbon brush by reparier
running
Excessive wearout of carbon brush
Ring fire caused by shortcircuit in
rotor winding shortcircuit
Ring fire caused by shortcircuit in
commutator segment
Overvoltage in supply power
Disconnection between carbon brush
and commutator
Excessive machinery noise Motor failure, edge friction or
bearing damage
Gear wheel failure
Failed to reach rated power Electrocircuit overload due to lighting
device, public utility or other electric
appliances
Machine superheating Electromotor overload
Insufficient motor cooling
Excessive mechanical Rotor damage
vibration
Gear wheel damage
Improper installation of cutting blade
or grinding disc
Substandard cutting effect or Severe wear of cutting blade or
grinding effect grinding disc
Spare parts list and drawing Please download files on www.maxpro-tools.com
Replace carbon brush
Check mechanical part by repairer
Regulate supply voltage
Replace switchboard by repairer
Replace carbon brush by reparier
Check or replace rotor by repairer
Check or replace rotor by repairer
Regulate supply voltage
Replace carbon brush
Check or replace motor or bearing by
repairer
Replace gear wheel or rotor by
repairer
No use of public utility or other
electric appliances on machine-
connected electrocircuit
Overload protection
Dedust air outlet
Replace electric machine rotor by
repairer
Replace gear wheel or rotor by
repairer
Redo with reference to installation
specification
Replace cutting blade or grinding disc
GB 9